Ihold – Hold current: Maximum current device will pass without interruption in 23°C still air.
Itrip – Trip current: Minimum current that will switch the device from low resistance to high resistance in 23°C still air.
Vmax: Maximum continuous voltage device can withstand without damage at rated current.
Imax: Maximum fault current device can withstand without damage at rated voltage.
Pd: Power dissipated from device when in the tripped state in 23°C still air.
Ri (min.): Minimum resistance of device as supplied at 23°C unless otherwise specified.
R1(max.): Maximum resistance of device when measured one hour post reflow (SMD) or one hour post trip (radial-leaded device) at 23°C unless otherwise specified.
• Insulating material: Cured epoxy resin meeting UL 94V0 requirements
Recommended Reworking Conditions with Soldering Iron
• Soldering Iron Tip Temperature: 360°C max.
• Solder Time: 3 seconds max.
• Distance from Thermistor: 2mm min.
1011
BU-SB111164
Page 3 of 4
Data Sheet 4399
Packaging/Taping Specifications
Description
Sprocket hole pitch
Ordinate to adjacent component lead:
PTR016V0090~PTR016V0250
PTR016V0300~PTR016V1100
PTR016V1200~PTR016V1500
Device pitch:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1400
PTR016V1500
Lead spacing
Carrier tape width
Top distance between tape edges
Hold-down tape width
Sprocket hole position
Abscissa to top:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1500
Abscissa to plane
(straight lead)
(kinked lead)
Sprocket hole diameter
Lead protrusion
Tape thickness
Body lateral deviation
Body tape plane deviation
Reel width
Reel diameter
Arbor hole diameter
Core diameter
* See Dimensions table.
IEC
Mark
P0
P1
P1
P1
P
P
P
C
W
W0
W1
W2
H1
H1
H
H0
D0
L1
t
Δ
h
Δ
p
W3
n0
n
Dimension Tolerance
(mm)
(mm)
12.7
±0.3
3.6
4.5
7.2
12.7
25.4
38.1
*
18
3.0
12
9.0
32.2
47.5
18.0
16.0
4
1
0.9
0
0
56
340
31
80
±1.0
±1.0
±1.0
±1.0
±1.0
±1.0
--
±1.0
Max.
±1.0
+0.75/-0.5
Max.
Max.
+2/-0
±0.5
±0.2
Max.
Max.
±1.0
±1.3
Max.
±10
±1
Min.
Style 1 - PTR016V0090, PTR016V0110, PTR016V0135,
PTR016V0160-PTR016V1000
Style 2 - PTR016V1200-PTR016V1500
Reel Specifications
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is
intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change
design or construction of any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information con-
tained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Life Support Policy: Cooper Bussmann does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life sup-
port systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result
I am a novice. I have an assignment in school and want to use the TX2440 development board. I watched the video, but I still don't know how to complete my project. I just want a simple display interfa...
w5100 is a chip with built-in network protocol. I will not go into details. I will just talk about the interrupt mode application. This application uses the TCP/IP network protocol, and the microcontr...
The principle of saving Internet fees by this software: (only applicable to the case of time-based charging) For example, if two people A and B share a router, it is inconvenient for A to disconnect f...
There is no empty statement in the standard C language. But in the C language programming of single-chip microcomputer, it is often necessary to use several empty instructions to produce a short delay...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
