Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
[align=left][font=微软雅黑]In our daily life, we often use transformers. We can see transformers in TV sets, radio recorders, air conditioners and other electrical appliances. So what are the common trans...
[Photos and text] On the application of hard disk technology in slow motion production July 26, 2006 9:43 Source: World Radio and TelevisionAuthor: Mr. Sheng Xiaohui, video engineer of the Technical O...
In order to prevent traffic accidents, when the intelligent detection device of the car detects danger ahead, it must send a warning message to the driver. The voice alarm clearly reminds the drive...[Details]
Today's portable medical devices allow patients to diagnose and treat themselves, move around freely, and even use the devices when they are out and about. To achieve the "easy to carry" feature, po...[Details]
This article discusses how to use an ultra-low-power RF transceiver chip from Zarlink Semiconductor for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices to achiev...[Details]
With the continuous improvement of living standards and the increase in the proportion of urban aging, the household use of medical electronic equipment has gradually become a trend. Among them, the...[Details]
At present, a hot spot for the research and development of hearing aids abroad is concentrated in China. To be more precise, it is based on the research of Chinese language and speech, and the deve...[Details]
0 Introduction
At present, the analysis of intra-pulse signals in pulse radar has always been a hot topic and difficulty in research. How to measure the intra-pulse carrier frequency more ...[Details]
Designers of handheld products such as cell phones, digital cameras, MP3 players and personal digital assistants (PDAs) are continually challenged to deliver more functionality in a smaller form...[Details]
There are many ways to attenuate signals. The most commonly used method is to divide the voltage using resistors. The common circuits are as follows:
Oscilloscope pre-stage attenuation c...[Details]
introduction
Like other
portable
electronic products,
blood flow parameter detectors
need to be small, thin, durable, reliable, and have a long standby time. Therefore, system desi...[Details]
Overview
In recent years, the vigorous development of integrated circuits has created a huge space for the research and application of digital circuits. FPGA has low power consumption, high re...[Details]
Preface
For a long time, SD cards with Flash Memory as storage have been widely used in consumer electronic products due to their small size, low power consumption, erasable and non-volati...[Details]
Introduction
The MAX2116 P1db data is measured at specific combinations of RF and baseband gain over the adjustable range of these two gains. These data can be used to select gain control se...[Details]
According to In-Stat/MDR, the number of mobile phones with Bluetooth capabilities will reach at least 300 million by 2005. One of the clear evidences of the increasing adoption of Bluetooth is that...[Details]
Murphy's Law tells us that "what can go wrong, will go wrong". In the testing or production process of video equipment, problems often occur when we least want them to happen and when it is leas...[Details]
1. Basic circuit characteristics of power amplifier
The basic circuit of the complementary symmetrical OTL power amplifier is shown in Figure ①. Among them: C1 is the signal input coupling ele...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
