[font=normal 宋体, Arial, Helvetica, sans-serif][color=#000000][size=12px]Working condition: Input 24V, output 12V/5A, IC specification is 12V/6A output. This leaves 17% margin, why does the IC hang aft...
The numbers generated by an analog-to-digital conversion chip are processed after entering 430 to produce a series of results, probably several hundred numbers, in float type, which cannot be stored i...
Hello everyone, I am Pi Ziheng, a serious technical guy. Today, Pi Ziheng will talk to you about the linker file in embedded development .
In the previous lesson "Source Files (.c/.h/.s)" , Pi Ziheng ...
[i=s]This post was last edited by xld0932 on 2021-2-18 00:17[/i]1. LCD schematic diagram
The LCD part uses the GD32E503's EXMC (external memory controller) peripheral, which is used to access various ...
I/O Devices
The device model is also based on the kernel object modelCurrently supported I/O device types are as follows:
RT_Device_Class_Char /* Character device */
RT_Device_Class_Block /* Block dev...
:loveliness: Introduction: This article is a character feature published on the website of [i]《[/i]Financial Times. The protagonist of the article is Lars Bak, the developer of Google Chrome V8 engine...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
