2. Parameter verified during line and load regulation tests. Regulation is specified for 10% to 100% loading on all outputs.
3. Auxiliary output regulation is not maintained if main output load is less than 10%.
4. Auxiliary outputs require at least 10% loading for specified regulation. Voltage may increase at lighter loads and is ultimately limited by overvoltage zener diodes.
5.Unless otherwise specified, “Rated” load is 20W on the main (+5 volt) output and 15 watts each on the auxiliary (±15 volt) outputs. Load currents of up to 5A and ±1.5A on the main
and auxiliary outputs respectively are acceptable as long as the total output power does not to exceed 50 watts. Values in [ ] brackets reflect “-H" option SEE hardened version
performance. The "-H" option incorporates alternative FET technologies providing a >82 MeV•cm2 /mg (Gold Ion) SEE capability to the design.
6. Guaranteed for a D.C. to 20MHz bandwidth. Tested using a 20kHz to 10MHz bandwidth.
7. Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in excess of the maximum limit may interfere with the
proper operation of the converter’s overload protection, causing erratic behavior during turn-on.
8. Overload power dissipation is defined as the device power dissipation with the load set such that VOUT = 90% of nominal.
9. Load step transition time ? 10
μs.
10. Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of its steady state value.
11. Line step transition time ? 100
μs.
12. Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the inhibit pin (pin 3) to the point where VOUT = 90% of nominal.
13. Load Regulation relative to output voltage at 50% rated load.
14. Line Regulation relative to output voltage at 120Vdc input.
15. For operation at temperatures between +85°C and +125°C, derate power linearly from 50 watts to zero. Parameter limits are not guaranteed.
I'm working on an infrared controlled clock and I'm stuck. I've been debugging it for a long time but I can't get it done. Has anyone done it before and can send me the program? Thank you. Since I am ...
SCCB bus SCCB is a simplified I2C protocol. SIO-1 is the serial clock input line, and SIO-O is the serial bidirectional data line, which are equivalent to SCL and SDA of the I2C protocol respectively....
WebUSB DFU is a USB firmware update protocol that can be used through the Chrome browser on systems that support WebUSB, such as Win10, Android, and MacOS.Build process:Build in Windows 10Install cmak...
[b] I want to buy a book, but there are too many books and I don’t know which one to choose. Please help me. Has anyone read "FPGA/CPLD Digital System Design Examples Based on Quartus2"? Please share ...
Actually, I already have a lot of things in mind, but I am still a little worried that I will forget what to say when I see so many people on site, haha. So I have been working hard to memorize recent...
While
the solid-state battery
industry is still engaged in a long technological marathon for
the "ultimate solution" for
electric vehicles
, some companies have begun looking for mor...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
Logic analyzers are widely used tools in digital design verification and debugging. They can verify the proper functioning of digital circuits and help users identify and troubleshoot faults. They ...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
The complexity of the integrated circuits (ICs) used in electronic systems in vehicles is increasing. They aim to execute artificial intelligence (AI) algorithms to control autonomous driving funct...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
Industrial computers with GPUs leverage powerful parallel processing to build deep learning models to analyze and respond to optical inputs. The systems develop an understanding of visual data to i...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]