EEWORLDEEWORLDEEWORLD

Part Number

Search

LQSW6331MEUB35

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 420V, 20% +Tol, 20% -Tol, 330uF,
CategoryPassive components    capacitor   
File Size52KB,2 Pages
ManufacturerNichicon
Websitehttp://www.nichicon.co.jp
Environmental Compliance
Download Datasheet Parametric View All

LQSW6331MEUB35 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 420V, 20% +Tol, 20% -Tol, 330uF,

LQSW6331MEUB35 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid763906093
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance330 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter30 mm
dielectric materialsALUMINUM
length35 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package formSnap-in
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)420 V
ripple current1420 mA
seriesQS
ALUMINUM ELECTROLYTIC CAPACITORS
QS
Snap-in Terminal type, 105°C High speed charge-discharge.
series
Suited for high frequency regenerative voltage for AC servomotor,
general inverter.
Suited for equipment used at valtage fluctuating area.
Suited for rectifier circuit of voltage doubler
Compliant to the RoHS directive (2002/95/EC).
QS
Hi speed
charge-
discharge
GU
Specifications
Item
Performance Characteristics
Category
Temperature Range
Rated
Voltage Range
Rated
Capacitance Range
Capacitance Tolerance
Leakage Current
25 to +105
°C
350 to 450V
82 to 820µF
± 20% at 120Hz, 20°C
1
3 CV
(
µ
A) (After 5 minutes' application of rated voltage [C : Rated Capacitance(µF), V : Voltage ( V ) ]
Measurement frequency : 120Hz,
Temperature : 20°C
450
0.20
Rated voltage (V)
tan
δ
(MAX.)
Rated voltage (V)
350
0.15
400
0.15
420
0.15
Tangent of loss angle (tan
δ)
Stability at Low Temperature
Impedance ratio ZT/Z20(MAX.)
350 to 450
Z
25°C / Z+20°C
8
Measurement frequency : 120Hz
Endurance of charge-
discharge behavior
After an application of charge-discharge voltage for 50million times
(charge-discharge voltage difference(∆V) = rated voltage
×
0.35, cycle
6Hz) capacitors shell meet the characteristics requirement listed at
right.
Capacitance change
tan
δ
Leakage current
Appearance
Within ±20% of the initial
capacitance
value
300% or less than the initial specified value
Less than or equal to the initial specified value
There shell be found to remarkable abnormality on the capacitor
Within ±20% of the initial
capacitance
value
200% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
The specifications listed at right shall be met when the capacitors are restored
to 20°C after D.C. bias plus rated ripple current is applied for 3000 hours at
105°C, the peak voltage shall not exceed the rated voltage.
Capacitance change
tan
δ
Leakage current
Shelf Life
Marking
After storing the capacitors under no load at
105
°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C,
they shall meet the specified value for
endurance
characteristics listed above.
Printed with white color letter on black sleeve.
Drawing
Polarity bar
Sleeve (P.E.T.)
φD
+1.5MAX.
Type numbering system (Example : 400V 180
µ
F)
1
2
3
4
5
6
7
8
9
10 11 12
13 14
L QS 2 G 1 8 1 ME L A 3 0
Case length code
Case dia. code
Configuration
10
L
±
2
Capacitance tolerance (±20%)
Rated capacitance (180µF)
Rated voltage (400V)
4.0±0.5
Pressure relief vent
0.8
10
±
0.1
+0.2
-0.1
.2
+0 .1
.8
-0
φD
22
25
30
35
Code
Z
A
B
C
Series name
Type
0
4.0±0.5
Please contact to us if other configurations are required.
2.5
1.5
+0.2
-0.1
(Terminal dimensions)
2-2φ±0.1
(PC board hole dimensions)
The other terminal is also available upon request.
Please refer page 272 for schematic of dimensions.
Minimum order quantity : 50pcs.
Dimension table in next page.
CAT.8100Z
Help with hard disk DMA reading and writing problems
Hello everyone, I use Tornado 2.2 and need to read and write hard disks, but I found that ataDrv.c says "DMA is not supported in this release". After testing, I found that the reading and writing spee...
Alan1987 Embedded System
Transistor emitter follower circuit
In many electronic circuits, in order to reduce the impact of the subsequent circuit on the previous circuit and when the output of some previous circuits requires a stronger load-carrying capacity (t...
fighting Analog electronics
Looking to buy second-hand stm32f407 board
Looking to buy a second-hand stm32f407 development board, the minimum system is fine...
House1989 Buy&Sell
Discussion on TI DSP encryption issues (transferred)
At present, the most commonly used TI DSPs are the three series of C2000, C5000 and C6000. C2000 is TI's entry-level DSP, mainly used in industrial control fields, such as motor control (variable freq...
安_然 Microcontroller MCU
I'm begging for the Verilog program for tft
If anyone has a Verilog program to drive TFT, can you share it with me? I will be very grateful!...
whf715 FPGA/CPLD
Implementation of MODBUS protocol on TI DSP TMS320F22335
[p=28, 2, left][color=rgb(0, 0, 0)]The instruments I made became more and more complex, and I needed to use DSP. I began to transplant the microcontroller's functions to DSP little by little. [/color]...
Aguilera DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 282  2462  1412  2857  2364  6  50  29  58  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号