SCOPE: QUAD SPST CMOS ANALOG SWITCHES
Device Type
01
02
Generic Number
DG201AA(x)/883B
DG202A(x)/883B
Case Outline(s).
The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter
L
K
Z
Mil-Std-1835
CDFP4-F16
GDIP1-T16 or CDIP2-T16
CQCC1-N20
Case Outline
Package Code
16 LEAD FLATPACK
F16
16 LEAD CERDIP
J16
20-Pin Ceramic LCC
L20
Absolute Maximum Ratings
Voltage Referenced to V-
V+ ...................................................................................................................................... 44V
GND ................................................................................................................................... 25V
Digital Inputs, V
S
, V
D
(Note 1) ......................................................... -2V to (V
+
+2V)or 20mA,
whichever occurs first
Current, Any terminal except S or D ............................................................................... 30mA
Continuous Current, S or D ............................................................................................. 20mA
(Pulsed at 1ms, 10% duty cycle max) ...................................................................... 70mA
Lead Temperature (soldering, 10 seconds) ........................................................................ +300°C
Storage Temperature ........................................................................................... -65°C to +150°C
Continuous Power Dissipation ............................................................................ T
A
=+70°C
16 lead Flatpack (derate 6.1mW/°C above +70°C) ................................................. 485mW
16 lead CERDIP(derate 10mW/°C above +70°C) ................................................... 800mW
20-Pin LCC (derate 9.1mW/°C above +70°C) ........................................................ 727mW
Junction Temperature T
J
.................................................................................….. +150°C
Thermal Resistance, Junction to Case,
ΘJC:
Case Outline 16 lead Flatpack ...........................................................…... 65°C/W
Case Outline 16 lead CERDIP.............................................................….. 50°C/W
Case Outline 20-Pin LCC ....................................................................…. 20°C/W
Thermal Resistance, Junction to Ambient,
ΘJA:
Case Outline 16 lead Flatpack ...........................................................…. 165°C/W
Case Outline 16 lead CERDIP..........................................................…... 100°C/W
Case Outline 20-Pin LCC .................................................................….. 110°C/W
Recommended Operating Conditions.
Ambient Operating Range (T
A
) .............................................................. -55°C to
+125°C
NOTE 1: Signals on S
X
, D
X
, or IN
X
exceeding V
+
or V
-
are clamped by internal diodes, and are
also internally current limited to 25mA.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of DG201A/DG202/883B
19-0041
Page 2 of
Rev. C
6
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
1
1*, 2, 3, 9
1, 2, 3, 9, 10**, 11**
1
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
*
**
PDA applies to Subgroup 1 only.
Subgroups 10 and 11, if not tested shall be guaranteed to the limits of Table 1.
----------------------------
Electrical Characteristics of DG201A/DG202/883B
19-0041
Page 5 of
Rev. C
6
Talking about work
京公网安备 11010802033920号
EEWORLD
