EEWORLDEEWORLDEEWORLD

Part Number

Search

PCF1206P-25-576KCT1

Description
RESISTOR, METAL FILM, 0.125W, 0.25%, 25ppm, 576000ohm, SURFACE MOUNT, 1206, CHIP
CategoryPassive components    The resistor   
File Size946KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PCF1206P-25-576KCT1 Overview

RESISTOR, METAL FILM, 0.125W, 0.25%, 25ppm, 576000ohm, SURFACE MOUNT, 1206, CHIP

PCF1206P-25-576KCT1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1236941032
package instruction, 1206
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPRECISION, LASER TRIMMABLE
JESD-609 codee3
Manufacturer's serial numberPCF
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature125 °C
Package shapeRECTANGULAR PACKAGE
method of packingTR
Rated power dissipation(P)0.125 W
Rated temperature70 °C
resistance576000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyMETAL FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.25%
Operating Voltage150 V
Precision Surface
Mount Resistors
PCF Series
Precision metal lm technology
Extended ohmic range 1R - 3M
Precision to ±0.01% and 5ppm/°C
TCR grades 50, 25, 15, 10, 5ppm/°C
Passivated range for superior humidity performance
Load life stability and humidity to 0.05%
Electrical Data - Standard Range
Type
PCF0201
TCR
(ppm/ºC)
50
25
50
25
15
10
5
50
25
15
10
5
50
25
15
10
5
50
25
15
10
5
50
25
15
10
5
50
25
15
10
5
50
25
15
10
5
Power
(W)
0.031
Limiting Element
Voltage (V)
15
Ohmic Value Range*
0.5%
49R9-33K
1
49R9-5K
1
10R-205K
0.063
25
-
2R-1M
0.063
50
-
1R-2M
0.1
100
-
1R–2M5
0.125
150
-
1R–2M5
0.2
150
-
1R–3M
0.25
150
-
1R–3M
0.5
150
-
4R7-1M
4R7-332K
4R7-332K
24R9-15K
4R7-2M
4R7-511K
4R7-511K
24R9-30K
2
4R7-2M5
4R7-511K
4R7-1M
24R9-50K
2
4R7-2M5
4R7-1M
4R7-1M
24R9-50K
2
4R7-3M
4R7-1M
4R7-1M
24R9-100K
4R7-3M
4R7-1M
4R7-1M
24R9-100K
24R9-500K
-
24R9-500K
24R9-500K
24R9-50K
-
24R9-500K
24R9-50K
-
24R9-200K
24R9-30K
-
-
24R9-100K
49R9-33K
49R9-12K
49R9-5K
-
0.25%
0.1%
-
-
0.05%
0.01%
PCF0402
PCF0603
PCF0805
PCF1206
PCF1210
PCF2010
PCF2512
* Standard values E24 or E96. Other values may be available by request.
Note 1: PCF0201 also available in 1% tolerance. Note 2: Higher values available on request.
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyn’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
08.10
© Welwyn Components Limited
Bedlington Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 Facsimile: +44 (0) 1670 829465 Email: info@welwyn-tt.com Website: www.welwyn-tt.com
I made a small program for msp430fr5739
I bought a 5739 board in a group purchase forum before, but it has been lying around. Recently, I took it out and used it again for a project.I wrote a small program in my spare time. P1.1 does adc sa...
z7turn Microcontroller MCU
Is there any difference between these two circuits?
Is it just the difference between a transistor and an operational amplifier? Are they essentially the same?...
wazai Analog electronics
Question about XILINX V5 series SX95T-1
XILINX V5 series SX95T-1 now samples 337.5M data, dual-edge sampling, similar to DDR, but the bus is LVDS25, the data rate is 675M, use OFFSET IN to constrain the sampling data, no matter how to adjus...
eeleader FPGA/CPLD
Microwave Software Experience
How to simulate microstrip circuits with ADS2003 How to set solutionfrequency in hfss9 How to view the directional map in hfss9 How to add two polarization incident plane waves of HFSS90TE and TM ? Ho...
JasonYoo MCU
Learning simulation + chopper type op amp and its noise
[i=s] This post was last edited by dontium on 2015-1-23 11:42 [/i] Original link: [url]deyisupport./blog/b/signalchain/archive/2013/07/10/51467.aspx [/url] Chopper-stabilized op amps have developed to...
zca123 Analogue and Mixed Signal
Help~How can I make the PCB package of this component according to the picture?
How can I draw the PCB package of this original part (HDR-E26FSG1+) according to the picture? I only found these materials on the Internet. I can draw the appearance dimensions, but I don’t understand...
卡卡fantic PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 37  450  1093  1803  481  1  10  23  37  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号