RS207 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Discrete semiconductor> diode> RS207

RS207: DescriptionBRIDGE RECTIFIER DIODE; CategoryDiscrete semiconductor diode; File Size21KB，2 Pages; ManufacturerFORMOSA; Websitehttp://www.formosams.com/

Download Datasheet Parametric Compare View All

RS207 Overview

BRIDGE RECTIFIER DIODE

RS207 Parametric

Parameter Name	Attribute value
Maker	FORMOSA
Reach Compliance Code	unknow
Configuration	BRIDGE, 4 ELEMENTS
Diode type	BRIDGE RECTIFIER DIODE
Maximum forward voltage (VF)	1 V
Maximum non-repetitive peak forward current	50 A
Number of components	4
Maximum operating temperature	125 °C
Maximum output current	2 A
Maximum repetitive peak reverse voltage	1000 V
surface mount	NO

Preview

Download Datasheet

View All

RS201

SINGLE PHASE 2.0 AMP BRIDGE RECTIFIERS

THRU

RS207

VOLTAGE RANGE

50 to 1000 Volts

CURRENT

2.0 Amperes

RS-2

.510(13.0)

.472(12.0)

FEATURES

* Ideal for printed circuit board

* Low forward voltage

* Low leakage current

* Polarity: marked on body

* Mounting position: Any

* Weight: 2.74 grams

.035(0.9)

.028(0.7)

DIA.

.50

MIN.

(12.7)

.160(4.1)

SPACING

.140(3.6)

.260(6.5)

.240(6.1)

.730(18.5)

.690(17.5)

.125

(3.2)

Dimensions in inches and (millimeters)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating 25 C ambient temperature uniess otherwies specified.

Single phase half wave, 60Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

TYPE NUMBER

Maximum Recurrent Peak Reverse Voltage

Maximum RMS Voltage

Maximum DC Blocking Voltage

Maximum Average Forward Rectified Current

.375"(9.5mm) Lead Length at Ta=50 C

Peak Forward Surge Current, 8.3 ms single half sine-wave

superimposed on rated load (JEDEC method)

Maximum Forward Voltage Drop per Bridge Element at 1.0A D.C.

Maximum DC Reverse Current

Ta=25 C

at Rated DC Blocking Voltage

Operating Temperature Range, T

Storage Temperature Range, T

STG

Ta=100 C

RS201 RS202 RS203 RS204 RS205 RS206

100

200

140

200

400

280

400

2.0

1.0

500

-65 +125

-65 +150

600

420

600

800

560

800

RS207 UNITS

1000

700

1000

RS207 Related Products

	RS207	RS206	RS205	RS204	RS203	RS202	RS201
Description	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	2 A, 600 V, SILICON, BRIDGE RECTIFIER DIODE	2 A, 400 V, SILICON, BRIDGE RECTIFIER DIODE	2 A, 200 V, SILICON, BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	2 A, SILICON, BRIDGE RECTIFIER DIODE
Maker	FORMOSA	FORMOSA	FORMOSA	FORMOSA	FORMOSA	FORMOSA	FORMOSA
Reach Compliance Code	unknow	unknow	unknow	unknow	unknow	unknow	unknow
Configuration	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS	BRIDGE, 4 ELEMENTS
Diode type	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE	BRIDGE RECTIFIER DIODE
Maximum forward voltage (VF)	1 V	1 V	1 V	1 V	1 V	1 V	1 V
Maximum non-repetitive peak forward current	50 A	50 A	50 A	50 A	50 A	50 A	50 A
Number of components	4	4	4	4	4	4	4
Maximum operating temperature	125 °C	125 °C	125 °C	125 °C	125 °C	125 °C	125 °C
Maximum output current	2 A	2 A	2 A	2 A	2 A	2 A	2 A
Maximum repetitive peak reverse voltage	1000 V	800 V	600 V	400 V	200 V	100 V	50 V
surface mount	NO	NO	NO	NO	NO	NO	NO

Recommended Resources

Circuit a using relay normally closed contact shunt trip coil method

Ventilation fan automatic control circuit

Voltage doubler rectifier electronic ballast circuit diagram

5V regulated power supply circuit using voltage doubler rectification

Computer motherboard circuit diagram 820 1_26

What is the replacement for clock() in VC++ EVC?: As the title says, the project needs to set a timeout and use clock() + time to set the timeout time, and then compare whether the current clock() is greater than the set time to determine the timeout...; 263775063 Embedded System

Application issues of op amps: A differential input amplifier, no matter it is bilateral input or unilateral input, I have seen many circuit diagrams that add a 5V pull-up resistor to the output pin (I don't know if this statement ...; 木易725 Analog electronics

Tutorial for using IAR V6 [PPT]: [local]1[/local][[i]This post was last edited by dontium on 2012-5-6 19:29[/i]]...; dontium MCU

Detailed explanation of UART, SPI, IIC and their differences and connections: The difference is of course the name: UART (Universal Asynchronous Receiver Transmitter) SPI (Serial Peripheral Interface); I2C (INTER IC BUS) The difference is in the electrical signal line: The SPI ...; fish001 Microcontroller MCU

Introduction to the Oscilloscope's Auto-Setup and Auto-Range: The automatic function of an oscilloscope mainly refers to the automatic setting and automatic range of the oscilloscope. Please note that it is not the same as the automatic trigger in the trigger, s...; Micsig麦科信 Test/Measurement

Question about making a timer: I want to make a timer, the interface is like this, two buttons, one start, one stop. Start, the timer will start counting, stop, the timer will stop. Now I only know OnTimer, settime, how to display ...; fdsa235236 Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components