EEWORLDEEWORLDEEWORLD

Part Number

Search

SSN08B6041FPLF13

Description
Array/Network Resistor, Bussed, Thin Film, 0.1W, 6040ohm, 100V, 1% +/-Tol, -50,50ppm/Cel, 1915,
CategoryPassive components    The resistor   
File Size160KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

SSN08B6041FPLF13 Overview

Array/Network Resistor, Bussed, Thin Film, 0.1W, 6040ohm, 100V, 1% +/-Tol, -50,50ppm/Cel, 1915,

SSN08B6041FPLF13 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeBussed
Number of terminals8
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height1.55 mm
Package length4.89 mm
Package formSMT
Package width3.9 mm
method of packingTR, 13 Inch
Rated power dissipation(P)0.1 W
resistance6040 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesSSN-B
size code1915
technologyTHIN FILM
Temperature Coefficient-50,50 ppm/°C
Tolerance1%
Operating Voltage100 V
Nichrome Resistor Networks
on Silicon Substrates
S Series: SQSxxA
1
, SQSxxB, SSNxxA, SSNxxB,
SSWxxA, SSWxxB, SPDxxA, SPDxxB
Isolated and bussed circuits
Thin film resistor network
RoHS compliant
Not Recommended for New Designs
For alternative see SQS - http://www.irctt.com/file.aspx?product_id=214&file_type=datasheet,
SPD - http://www.irctt.com/file.aspx?product_id=225&file_type=datasheet,
SSN & SSW - http://www.irctt.com/file.aspx?product_id=215&file_type=datasheet
Features
Precision Nichrome Resistors on Silicon
Industry Standard Packaging
Ratio Tolerances
TCR Tracking Tolerances
Passivation coating provides protection in humid environments
JEDEC 95
< ± 0.05%
< ± 5 ppm/°C
Schematics
Electrical
2
Standard Resistance Range
3
Resistor Tolerances
Ratio Tolerances
TCR
Operating Temperature Range
Interlead Capacitance
Insulation Resistance
Maximum Operating Voltage
Noise, Maximum (MIL-STD-202, Method 308)
Resistor Power Rating at 70°C
1 xx denotes package pin count. Reference package type section in this data sheet for description.
2 Specifications subject to change without notice.
3 E96 codes available.
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
1K ohms to 100K ohms (Isolated)
1K ohms to 30K ohms (Bussed)
± 0.25%
± 0.05%
TCR table
-55°C to +125°C
< 2 pF
10,000 Megohms
100 Vdc or v PR
-25 dB
0.1 Watts
© TT electronics plc
10.13
CxImage ported to wince problem
I ported Cximage to wince, generated a dll, and then called it in the demo main program. I put the demo and Cximage projects under one solution, and then set the dependencies. There are always program...
ali50m Embedded System
DSP2812 Programming Problems
Help! ! Urgent! I am programming a single closed-loop incremental PID closed-loop control of a DC motor speed, but I don't know how to program it to measure speed and perform PID calculation using the...
Les DSP and ARM Processors
Math Equation Clock: a clock that tests your math ability
For some people, math is a nightmare. But some designers want to test you and bring you this arithmetic clock Math EquationClock. The answers to the 12 equations correspond to the 12 hours of the day....
soso Talking
Will controlling the LED in this way cause current bias?
My simulation uses a constant current IC to control the LED to light up. The constant current can be an LDO circuit or a DCDC circuit. Of course, in actual situations, the connection between each LED ...
小太阳yy LED Zone
Question about LPC1766 external counter
Hello everyone, I recently encountered a problem when using lpc1766. I found that the count control register CTCR had no effect after configuration. It was still in timing mode and could not count ext...
dixiatie755 NXP MCU
A small piece of assembly code for advice
My goal is to change the output status code of a certain bit in the port as follows: inp(int addr) { unsigned char al; __asm { push edx mov edx, DWORD PTR addr in al, dx and eax, 0xff pop edx } return...
adadad111 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 219  2113  580  281  2426  5  43  12  6  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号