7V for a duration of 1ms does not damage the device.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Operating Temperature Range .......................... -40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(V
BATT
= 1.2V to 5.5V, V
CC
= 1.2V to 5.5V, T
A
= -40°C to +85°C, unless otherwise specified. Typical values are at T
I recently made a board, but the lines were too dense. I adjusted the spacing to 5 mil, but the PCB manufacturer said they couldn't do it. I was very depressed....
If the picture is shown, the .h files included in the .c file should be displayed normally, but now it is not displayed, and the compilation is normal. Please give me some advice! !...
Dear experts, I am a beginner. I am using STM8S003F3 to debug hardware I2C. There are three devices on the bus, including STM8. When I reset the other two devices with MCU, I found that I2C was occupi...
SPI's CPOL=0, CPHA=1, falling edge data is written from the controller to the chip, and rising edge data is read from the chip to the controller. The falling edge of the first clock writes the MSB of ...
Recruiting reverse debugging personnel with high salary! Good treatment! At the same time recruiting C/C++/Delphi programmers Work location: Changchun City, Jilin Province Work nature: Full-time (part...
I encountered a problem when using VxWorks, which is described as follows: 1. The system has no applications, only a VXwroks system and timer, serial port, and network port drivers. 2. The system rese...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
The future energy storage hotspot is not coal or iron ore, but lithium. This lightest metal in nature may be the heaviest resource in the future energy landscape. China launched an ambitious electr...[Details]
1 Battery technology determines the fate of energy vehicles
Regardless of whether new energy vehicles are hybrid or pure electric vehicles, they cannot do without the core technology of batter...[Details]
The rapid development of the automobile industry has promoted the progress of global machinery, energy and other industries, as well as the development of economy, transportation and other aspects,...[Details]
0 Introduction
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The ways to reduce costs are: ① Use the Bluetooth data transmission...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
