7V for a duration of 1ms does not damage the device.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Operating Temperature Range .......................... -40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(V
BATT
= 1.2V to 5.5V, V
CC
= 1.2V to 5.5V, T
A
= -40°C to +85°C, unless otherwise specified. Typical values are at T
I have been in the school's Electronic Innovation Laboratory for six years at Harbin Engineering University. During these four years, the Innovation Laboratory provided me with a good learning environ...
[i=s]This post was last edited by Aguilera on 2018-12-24 20:41[/i] [size=4]1. GPIO[/size] [size=4]GPxMUX (function selection register),[/size] [size=4] GPxMUX.bit=0 is configured as I/O function. GPxM...
I have a string like this. Each line ends with a carriage return, and the hexadecimal is OD OA. I want to split the following string into lines, and execute it under WINCE. I would like to ask an expe...
During the debugging of the PCB board, a pin of component A is connected to a pin of component B, but the voltage between the two pins is not 0V, but 0.5V. Why is this? (Because the circuit in the fol...
1. After the PCB design is completed, how to choose the PCB material? The selection of PCB material must strike a balance between meeting the design requirements and mass production and cost. The desi...
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
1. Project Introduction
Beijing Benz-Daimler Chrysler Co., Ltd. is a joint venture between Beijing BAIC Group and Benz-Daimler Chrysler. In October 2005, it started to build a new automobile ...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
Various electronic and electromagnetic interference inside and outside the car often puts automotive electronic equipment in dangerous working conditions, degrading the performance of electronic eq...[Details]
SL11R is a 16-bit RISC microcontroller with a USB interface produced by Scanlogic. Its core processing speed reaches 48MIPS. It has rich hardware resources and 32-bit programmable I/O ports, and ca...[Details]
Abstract: Based on FPGA hardware, the image scaling with fixed magnification is realized. The 2D convolution operation is decomposed into 2 1D convolution operations. The input original image pixel...[Details]
Compared with traditional lighting fixtures, LED lamps do not need to use filters to produce colored light. They are not only highly efficient and pure in color, but also can achieve dynamic or gra...[Details]
1 Introduction
The development of fieldbus technology has made a big step forward in the process of control systems from closed to open. Open control systems based on fieldbus have begun to enter th...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
