Feature - No dead cycles between write and read cycles
Internally synchronized output buffer enable eliminates the
need to control
OE
Single R/W (READ/WRITE) control pin
Positive clock-edge triggered address, data, and control signal
registers for fully pipelined applications
4-word burst capability (interleaved or linear)
Individual byte write (BW
1
-
BW
4
) control (May tie active)
Three chip enables for simple depth expansion
3.3V power supply (±5%)
3.3V I/O Supply (V
DDQ
)
Power down controlled by ZZ input
Packaged in a JEDEC standard 100-pin plastic thin quad
flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch
ball grid array(fBGA).
The IDT71V65603/5803 are 3.3V high-speed 9,437,184-bit
(9 Megabit) synchronous SRAMS. They are designed to eliminate dead bus
cycles when turning the bus around between reads and writes, or writes and
reads. Thus, they have been given the name ZBT
TM
, or Zero Bus Turn-
around.
Address and control signals are applied to the SRAM during one clock
cycle, and two cycles later the associated data cycle occurs, be it read or write.
The IDT71V65603/5803 contain data I/O, address and control signal
registers. Output enable is the only asynchronous signal and can be used
to disable the outputs at any given time.
A Clock Enable (CEN) pin allows operation of the IDT71V65603/5803
to be suspended as long as necessary. All synchronous inputs are ignored
when (CEN) is high and the internal device registers will hold their previous
values.
There are three chip enable pins (CE1, CE2,
CE2)
that allow the user
to deselect the device when desired. If any one of these three are not
asserted when ADV/LD is low, no new memory operation can be
initiated. However, any pending data transfers (reads or writes) will be
completed. The data bus will tri-state two cycles after chip is deselected
or a write is initiated.
The IDT71V65603/5803 have an on-chip burst counter. In the burst
mode, the IDT71V65603/5803 can provide four cycles of data for a
single address presented to the SRAM. The order of the burst
sequence is defined by the
LBO
input pin. The
LBO
pin selects
between linear and interleaved burst sequence. The ADV/LD signal is
used to load a new external address (ADV/LD = LOW) or increment
the internal burst counter (ADV/LD = HIGH).
The IDT71V65603/5803 SRAM utilize IDT's latest high-performance
CMOS process, and are packaged in a JEDEC Standard 14mm x 20mm
100-pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array
(BGA) and 165 fine pitch ball grid array (fBGA) .
Pin Description Summary
A
0
-A
18
CE
1
, CE
2
,
CE
2
OE
R/W
CEN
BW
1
,
BW
2
,
BW
3
,
BW
4
CLK
ADV/LD
LBO
ZZ
I/O
0
-I/O
31
, I/O
P1
-I/O
P4
V
DD
, V
DDQ
V
SS
Address Inputs
Chip Enables
Output Enable
Read/Write Signal
Clock Enable
Individual Byte Write Selects
Clock
Advance burst address / Load new address
Linear / Interleaved Burst Order
Sleep Mode
Data Input / Output
Core Power, I/O Power
Ground
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
I/O
Supply
Supply
Synchronous
Synchronous
Asynchronous
Synchronous
Synchronous
Synchronous
N/A
Synchronous
Static
Asynchronous
Synchronous
Static
Static
5304 tbl 01
ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola, Inc.
It is said that opening windows in circuits can facilitate the passage of large currents. Could you please tell me how much more current can be passed with windows in circuits than without windows?...
I talked to a forum engineer about Guoxin a while ago, and talked about the expiration of M0 and the open sourceToday, I accidentally touched upon STC's family. There was no reason. I was just excited...
[i=s]This post was last edited by Tang Quan on 2016-11-30 10:18[/i] I have posted a post before: [url=https://bbs.eeworld.com.cn/thread-496527-1-1.html]https://bbs.eeworld.com.cn/thread-496527-1-1.htm...
The embedded devices we developed can communicate with each other using both straight-through and crossover cables. Does anyone know why? I am using the Realtelk 8201 network card chip?...
My company is going to do a project and needs an 8-inch touch screen. I am going to buy an 8-inch screen and asked the seller for technical support. They said that STM32 cannot support such a high-res...
After the microcontroller is powered on, if the clock system is not set, the default 800 kHz DCOCLK is used as the clock source of MCLK and SMCLK, and LFXT1 is connected to a 32768 Hz crystal and work...
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
Capable of providing precise and efficient thermal management for artificial intelligence computing power, intelligent sensing and autonomous driving systems
Shenzhen, ...[Details]
On August 18th, Galaxis, a specialist in integrated intelligent intralogistics robotics, officially unveiled its next-generation, ultra-narrow aisle forklift mobile robot, the "VFR Ultra-Narrow Ser...[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
A half-bridge is an inverter topology for converting DC to AC. A typical half-bridge circuit consists of two controller switches, a three-wire DC power supply, two feedback diodes, and two capacito...[Details]
With the gradual popularization of new energy vehicles in recent years, more and more people have been able to access and purchase electric vehicles. The structure of electric vehicles is composed ...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
introduction
The widespread use of air conditioner communication circuits began with the rise of household inverter air conditioners. With China's energy conservation and emission reduction in...[Details]
Silicon Labs (also known as "Silicon Labs"), an innovative leader in low-power wireless connectivity, will showcase its cutting-edge artificial intelligence (AI) and Internet of Things (IoT) solu...[Details]
This series of articles aims to help readers have a brief understanding of the Hongke KPA Automation system and to quickly get started with MoDK, including: an introduction to Hongke KPA Automation...[Details]
Since entering the electronic components industry, I've learned that electronic components come in different packaging types. Some people have argued that different types of components may look the...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
