BPM0J222M datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> capacitor> BPM0J222M

BPM0J222M: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum, 6.3V, 20% +Tol, 20% -Tol, 2200uF; CategoryPassive components capacitor; File Size344KB，2 Pages; ManufacturerGemmy Electronics Co., Ltd.

Download Datasheet Parametric View All

BPM0J222M Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 6.3V, 20% +Tol, 20% -Tol, 2200uF

BPM0J222M Parametric

Parameter Name	Attribute value
Objectid	1215511464
package instruction	,
Reach Compliance Code	unknown
ECCN code	EAR99
capacitance	2200 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
diameter	12.5 mm
dielectric materials	ALUMINUM
length	25 mm
Manufacturer's serial number	BPM(0J)
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package form	Radial
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	6.3 V
series	BPM(0J)
Terminal pitch	5 mm

Preview

Download Datasheet

View All

BPM

04 ½両極性標準品（85℃）

RADIAL TYPE BI-POLAR

シリーズ

SERIES

標準品

Standard

両極性品

Bi-polar

■

特長 FEATURES

・

極性反転回路用標準品

Standard size for reversing polarity circuit.

・

自動挿入用テーピング品を各種用意

Available in taping configuration for automatic insertion.

・

85℃ 1000 時間保証

Load Life : 85℃ 1000 hours.

■

仕様 SPECIFICATIONS

項目 Items

½ 用温度範囲

Operating Temperature Range

定格電圧範囲

Rated Voltage Range

静電容量範囲

Nominal Capacitance Range

静電容量許容差

Capacitance Tolerance

漏れ電流

Leakage Current

損失角の正接

Dissipation Factor

特性

Characteristics

−40 ＋85℃

∼

6.3 100V.DC

∼

0.47 6800μF

∼

±20％（20℃，120Hz)

I=0.03CV 又は 3μAのいずれか大きい値以下（5分値）

I=0.03CV or 3μA whichever is greater, after 5 minutes application of rated voltage.

定格電圧(V)

・120Hz

6.3

100

Rated Voltage

20℃

tanδ(MAX)

0.26

0.24

0.22

0.20

0.16

0.14

0.12

0.10

1000μFを越えるものについては、1000μFを増す毎に0.02を加えた値とする。

For capacitance of more than 1000μF, add 0.02 for every increase of 1000μF．

インピーダンス比 Impedance Ratio

定格電圧(V)

6.3

100

Rated Voltage

・120Hz

Z(-25℃)/Z(20℃)

Z(-40℃)/Z(20℃)

85℃中にて定格電圧を 250時間毎に極性反転し1000時間印加後、下記規格を満足する。

After 1000 hours application of rated voltage at 85℃, reversing polarity at each 250 hours.,

capacitors meet the characteristics requirements mentioned below.

静電容量変化率初期値の±20％以内

Capacitance Change Within ±20％ of initial value.

損失角の正接初期規格値の200％以下

Dissipation Factor

200％ or less of initial specified value.

漏れ電流初期規格値以下

Leakage Current

Initial specified value or less.

85℃1000時間無負荷放½後、上記高温負荷特性の規格を満足する。

（½し、JIS C-5102 4.4項の電圧処理後）

After leaving capacitors under no load at 85℃ for 1000 hours and applying voltage according to

JIS C-5102 4.4, they meet the specified value for load life characteristics listed above.

灰色チューブに黒色印刷

Black print on gray sleeve.

JIS C-5141 特性Ｗ

Characteristics Ｗ of JIS C-5141.

温度特性

Temperature Characteristics

高温負荷特性

Load Life

高温無負荷特性

Shelf Life

表示

Marking

Recommended Resources

Gas pendulum tilt sensor circuit diagram A

Insulation test of general frequency converter

Isolated and amplified platinum resistance temperature measurement circuit

Diode-transistor NOR gate circuit

Wien bridge type oscillator circuit

Voice + music speech synthesis series

What is the use of placing the interrupt flag in the interrupt program?: interrupt[PORT_vector]void PORT1(void){if(P1IFG&BIT0){Delay();if(P1IFG&BIT0){Execution body;P1IFG&=~BIT0;}}}Can this remove jitter? I feel that judging the interrupt flag in the interrupt program can ...; maihy1985 Microcontroller MCU

STM32DAC and PWM clock are not synchronized, please help: I use the internal DAC of the stm32L4 chip to generate a sine wave, and then use the timer's PWM to generate a square wave. However, I found through an oscilloscope that the two waveforms are not sync...; lulongqin12 stm32/stm8

Learn Analog + Learn Operational Amplifier Gain Error Design Guide: [i=s]This post was last edited by dontium on 2015-1-23 11:39[/i] [b][size=2]Operational Amplifier Gain Error Design Guide[/size][/b][size=2]deyisupport./blog/b/signalchain/archive/2013/10/01/51518.asp...; machinnneee Analogue and Mixed Signal

How to place component packages outside the Package Keepin area in Allegro: I set the Package Keepin area when drawing the PCB in Allegro. Now I want to place the DB25 connector on the edge of the PCB. Part of the component needs to go beyond the PCB frame, and of course it a...; 文心雕龙7 PCB Design

Joined the semiconductor industry since yesterday!: But I don't really know much about this industry, please give me some advice!...; mjiqng Talking

Push button switch.: Is there any problem with the program I wrote? (TM4C123GH6PM) (CCS) Actually it doesn't work. #include #include #include"inc/hw_ints.h" #include"inc/hw_nvic.h" #include"inc/hw_memmap.h" #include"inc/h...; amo_1 Microcontroller MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components