EEWORLDEEWORLDEEWORLD

Part Number

Search

S2BQ1422EX1

Description
Array/Network Resistor, Isolated, Metal Film, 0.7W, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, CHIP, LEAD FREE
CategoryPassive components    The resistor   
File Size299KB,5 Pages
ManufacturerThin Film Technology Corp (TFT)
Environmental Compliance  
Download Datasheet Parametric View All

S2BQ1422EX1 Overview

Array/Network Resistor, Isolated, Metal Film, 0.7W, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, CHIP, LEAD FREE

S2BQ1422EX1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1714253200
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPRECISION
The first element resistor14200 Ω
JESD-609 codee3
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature175 °C
Minimum operating temperature-40 °C
Package shapeRECTANGULAR PACKAGE
method of packingTR
Rated power dissipation(P)0.7 W
Rated temperature125 °C
Resistor typeARRAY/NETWORK RESISTOR
surface mountYES
technologyMETAL FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin (Sn)
Terminal shapeWRAPAROUND
Tolerance0.1%
SR02 & S2 (Published)
Page 1 of 5
Precision Resistor Networks
SR02
& S2 Series
Description
The
SR02
& S2 Series resistor networks are precision-class metal film components featuring tight resistance
tolerance and low values of temperature coefficient of resistance (TCR). This resistor network package
provides both excellent resistance ratio and TCR tracking.
Electrical
Parameter
Resistance range
Resistance ratio
tolerance:
Power rating per
package
Operating
temperature
Storage temperature
Power Derating Curve
Tolerance Table
Resistance Value
Range
10Ω - <20Ω
20Ω - <100Ω
100Ω -<15KΩ
SR02
& S2 series
10Ω - 30KΩ
(See Tolerance Table below
for further details)
±0.02% (Q)
±0.05% (A)
0.70 watts @125°C
(refer to derating curve)
- 40 to +175°C
- 55 to +125°C
Abs.
Resistance
Tolerance
Available
±0.05% (A)
±0.10% (B)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
±0.01% (T)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
±0.01% (T)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
Absolute TCR TCR Tracking
Tolerance
(ppm.°C)
(refer to note
Available
1& 2)
±25 ppm/°C
±5 (M)
(E)
±25 ppm/°C(E)
±2 (R)
±5 (M)
±5 ppm/°C (M)
±1 (X)
±2 (R)
±10 ppm/°C
±5 (M)
(Y)
±25 ppm/°C
(E)
±10 ppm/°C
±2 (R)
(Y)
±5 (M)
±25 ppm/°C
(E)
Note 1:
Ratio values greater
than 50:1 only available in ±5
ppm/°C TCR tracking
tolerance
Note 2 :
±1ppm/°C TCR
tracking only available for
identical resistance values.
15KΩ - Max
Mechanical
http://www.thin-film.com/web/tft.nsf/41acb363040f5be585256a7b001dcc4c/b48916af35... 10/23/2007
Key points of welding, introduction of manual welding method
[i=s]This post was last edited by bjhyyq on 2017-7-19 11:35[/i] [align=left][size=14px][b]Preheating 1:[/b]Put the soldering tip in full contact with the solder joint. Figure 1 shows how to heat the s...
bjhyyq PCB Design
Newbie~Help me with MSP430 program burning problem
I use IAR version 5.1, and the MCU model is MSP430F19. I can debug the software normally, but the following error will occur when the hardware is connected. The same error occurs when the MCU and emul...
我爱小恶习 Microchip MCU
CCS3.3编译错误 error:this declaration has no storage class or type specifier
The following error occurs when compiling the program with CCS3.3: error: this declaration has no storage class or type specifier error: declaration is incompatible with "volatile struct PIE_CTRL_REGS...
ndt126 DSP and ARM Processors
CC4024-----7-bit binary serial counter
CC4024 is a 7-bit binary serial counter. All counters are slave flip-flops. The counter counts on the falling edge of the clock. When CR is high, the counter is cleared, because a tear-off flip-flop i...
rain Analog electronics
About AD630
What is the function of the 10K ohm potentiometer connected to pins 34 and 56 in the figure? Why is it connected like this? Why are these four pins not listed in the simulation model on the official w...
K99_Z.H.Q Analog electronics
How to keep the AD schematic synchronized with the PCB after it is split?
I spent two schematics at the beginning, and after I finished drawing the PCB, the schematics looked a bit messy, so I divided the schematics into several more according to the functions. However, I f...
liyancao001 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 395  2199  1768  305  1686  8  45  36  7  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号