SO (derate 23.3mW/°C above +70°C)..........................1860mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TDFN
Junction-to-Ambient Thermal Resistance (θ
JA
) ...........42°C/W
Junction-to-Case Thermal Resistance (θ
JC
) ...............8.5°C/W
SO
Junction-to-Ambient Thermal Resistance (θ
JA
) ...........43°C/W
Junction-to-Case Thermal Resistance (θ
JC
) ..................7°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= 14V, I
OUT
= 1mA, C
IN
= 0.1µF, C
OUT
= 2.2µF, T
A
= T
J
= -40°C to +125°C, unless otherwise noted. Typical specifications are at
T
A
= +25°C.) (Note 2)
PARAMETER
Input Voltage Range
SYMBOL
V
IN
I
OUT
= 0A (MAX15006A/B/D)
I
OUT
= 0A (MAX15006C)
I
OUT
= 0A (MAX15007A/B)
I
OUT
= 0A (MAX15007C)
I
OUT
= 100μA
(MAX15006A/B/D)
I
OUT
= 100μA (MAX15006C)
Ground Current
I
GND
Regulator on,
measured at GND
I
OUT
= 100μA (MAX15007A/B)
I
OUT
= 100μA (MAX15007C)
I
OUT
= 1mA (MAX15006A/B/D)
I
OUT
= 1mA (MAX15006C)
I
OUT
= 1mA (MAX15007A/B)
I
OUT
= 1mA (MAX15007C)
I
OUT
= 50mA (MAX15006)
I
OUT
= 50mA (MAX15007)
I
OUT
= 60mA (MAX15006D)
Shutdown Supply Current
I
SHDN
Regulator off (MAX15007 only)
CONDITIONS
MIN
4
10
8
11
9
10.5
8.5
11.5
9.5
12
10
13
11
90
93
110
3
TYP
MAX
40
17
15
18
16
18
16
19
17
20
18
21
19
150
150
150
5
μA
μA
UNITS
V
2
Maxim Integrated
MAX15006/MAX15007
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
ELECTRICAL CHARACTERISTICS (continued)
(V
IN
= 14V, I
OUT
= 1mA, C
IN
= 0.1μF, C
OUT
= 2.2μF, T
A
= T
J
= -40°C to +125°C, unless otherwise noted. Typical specifications are at
T
A
= +25°C.) (Note 2)
PARAMETER
REGULATOR
Guaranteed Output Current
I
OUT
V
IN
V
IN
V
OUT
+ V
DO
V
OUT
+ V
DO
(MAX15006D only)
MAX15006A/D, MAX15007A
MAX15006B/MAX15007B
MAX15006C/MAX15007C
I
OUT
= 5mA, MAX15006B/MAX15007B
I
OUT
= 5mA, MAX15006C/MAX15007C
Dropout Voltage (Notes 4, 5)
V
DO
I
OUT
= 50mA, MAX15006B/MAX15007B
I
OUT
= 50mA, MAX15006C/MAX15007C
I
OUT
= 50mA, MAX15006A/MAX15007A
I
OUT
= 60mA, MAX15006D
Line Regulation
Load Regulation
Output Current Limit
Output Voltage Noise
Power-Supply Rejection Ratio
FB Threshold Voltage
FB Input Current
ENABLE LOGIC
Enable Threshold Voltage
Enable Threshold Hysteresis
Enable Pulldown Current
Enable to Regulation Time
THERMAL SHUTDOWN
Thermal Shutdown
Thermal Shutdown Hysteresis
T
SHDN
T
HYST
Junction temperature rising
+165
20
°C
°C
Internally pulled down to GND
(Note 6)
V
IL
V
IH
1.4
60
0.5
0.4
2
0.4
V
mV
μA
ms
PSRR
V
FB
I
FB
100Hz to 100kHz, I
OUT
=
50mA, C
OUT
= 2.2μF
V
OUT
= 3.3V
V
OUT
= 5V
1.2
-100
6V
V
IN
35V, I
OUT
= 1mA
0.7
0.7
80
115
179
66
1.23
1.26
+100
V
IN
= V
OUT
+ 3V, I
OUT
= 100μA to 50mA
V
IN
= V
OUT
+ 3V, I
OUT
= 100μA to 60mA
(MAX15006D)
50
60
3.25
4.925
1.8
30
30
300
300
3.3
5.0
3.35
5.075
10
53
60
525
600
1000
1000
0.25
1.5
1.5
350
%
mA
μV
RMS
dB
V
nA
%
mV
V
mA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Output Voltage (Note 3)
V
OUT
I
OUT
= 1mA
f = 100Hz, V
IN_RIPPLE
= 500mV
P-P
, I
OUT
= 50mA
I
LOAD
= 1mA (MAX15006C/MAX15007C only)
V
FB
= 0V, 1.5V (MAX15006C/MAX15007C only)
Limits at T
A
= -40°C are guaranteed by design.
Output voltage regulation is guaranteed for I
OUT
≥
5μA.
Dropout voltage is defined as (V
IN
- V
OUT
) when V
OUT
is 2% below the value of V
OUT
when V
IN
= V
OUT
+ 3V.
For V
OUT
= 3.3V, the 700mV dropout indicates V
OUT
does not reach 2% below V
OUT
at V
IN
= V
OUT
+ 3V at minimum 4V
input voltage.
Note 6:
Enable to regulation time is the time the output takes to reach 95% of its final value with V
Abstract: The network processor combines the high performance of ASIC and the programmable flexibility of RISC chips, and can provide both good processing speed and rich business support. NP4GS3 C is ...
A novice would like to ask a question about MOS tubes. In the resonant circuit shown in the figure below, when M1 and M2 are both turned on, that is, only the inductor L works in the circuit, L1 and L...
I have two questions for you. I am studying a waveform of two microcontrollers communicating. If the first pin is used as the clock signal, should the sampling between the second and third pins be bas...
:victory: I wish you all a happy Chinese New Year! We will be on holiday from tomorrow, February 1st. But don’t worry, we are still open and will not close! There are still waves of good activities du...
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
Since the beginning of this year, price wars have intensified, new models have been launched one after another, used cars with zero kilometers have become a hot topic, and the industry's internal c...[Details]
While the current industry consensus is that autonomous vehicles are robots and that their systems are managed using robotics-developed thinking, there are also cases where autonomous driving is ac...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
Preface
Low-voltage motors are widely used in nonferrous metallurgical plants. Their abnormal operation not only impacts normal production but can also threaten human life. Therefore, providin...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
introduction
With the development of society, people's requirements for the quality of refrigerated and frozen foods are constantly improving. The changes in food appearance and nutritional co...[Details]
introduction
In today's busy society, people experience chronic high stress, which in turn poses a significant threat to our health. Therefore, effectively relieving stress has become a pr...[Details]
0 Introduction
DVI (Digital Visual Interface) is a hot topic in current digital display research and application. Video processing technologies for DVI output not only address issues such as h...[Details]
The electric motor is one of the most widely used power equipment and plays a vital role in the national economy. However, its high failure rate causes huge economic losses to industrial and agricu...[Details]
In the exhibition halls of the 2025 World
Robot
Conference (WRC), robots of all shapes and sizes competed for attention. As the hustle and bustle of this industry event gradually subsided, ...[Details]
Electric vehicles are structurally composed of three main components: batteries, motors, and electronic controls. Power is transmitted from the battery to the motor, which in turn drives the vehicl...[Details]
Xenon lamp principle
Xenon lamps are high-pressure gas discharge lamps that are filled with a mixture of inert gases including xenon and do not have the filament of halogen lamps. They are ref...[Details]
The "China Electric Vehicle Charging Equipment Development Report (2024)" was compiled by the China Electric Vehicle Charging Infrastructure Promotion Alliance and Shenzhen Shenghong Electric Co., ...[Details]
NVIDIA Jetson + Isa K
solutions
for the humanoid field
A detailed explanation of the solution
, covering chip models, software platforms, development toolchains, application scenarios,...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
