V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Supply Current,
AutoShutdown Plus
Supply Current, Shutdown
Supply Current,
AutoShutdown Plus Disabled
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
Input Logic Threshold High
Transmitter Input Hysteresis
Input Leakage Current
Output Leakage Current
Output Voltage Low
Output Voltage High
RECEIVER INPUTS
Input Voltage Range
Input Threshold Low
Input Threshold High
Input Hysteresis
Input Resistance
2
SYMBOL
CONDITIONS
FORCEON = GND,
FORCEOFF
= V
CC
,
all R_IN idle, all T_IN idle
FORCEOFF
= GND
FORCEON =
FORCEOFF
= V
CC
, no load
MIN
TYP
MAX
UNITS
DC CHARACTERISTICS
(V
CC
= 3.3V or 5.0V, T
A
= +25°C)
1
1
0.3
10
10
1
µA
µA
mA
T_IN, FORCEON,
FORCEOFF
T_IN, FORCEON,
FORCEOFF
V
CC
= 3.3V
V
CC
= 5.0V
2
2.4
0.5
T_IN, FORCEON,
FORCEOFF
R_OUT (MAX3244E/MAX3245E), receivers
disabled
I
OUT
= 1.6mA
I
OUT
= -1.0mA
V
CC
- 0.6 V
CC
- 0.1
-25
T
A
= +25°C
T
A
= +25°C
V
CC
= 3.3V
V
CC
= 5.0V
V
CC
= 3.3V
V
CC
= 5.0V
3
0.6
0.8
1.2
1.5
1.5
1.8
0.5
T
A
= +25°C
5
±0.01
±0.05
0.8
V
V
V
±1
±10
0.4
µA
µA
V
V
+25
V
V
2.4
2.4
7
V
V
kΩ
Maxim Integrated
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
ELECTRICAL CHARACTERISTICS (continued)
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
TRANSMITTER OUTPUTS
Output Voltage Swing
Output Resistance
Output Short-Circuit Current
Output Leakage Current
V
CC
= 0V or 3V to 5.5V, V
OUT
= ±12V,
Transmitters disabled
All transmitter outputs loaded with 3kΩ to
ground
V
CC
= V+ = V- = 0V, transmitter outputs = ±2V
±5
300
±5.4
10M
±60
±25
V
Ω
mA
µA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MOUSE DRIVEABILITY
(MAX3244E/MAX3245E)
T1IN = T2IN = GND, T3IN = V
CC
,
T3OUT loaded with 3kΩ to GND,
T1OUT and T2OUT loaded with
2.5mA each
IEC 1000-4-2 Air Discharge
R_IN, T_OUT
IEC 1000-4-2 Contact Discharge
Human Body Model
AutoShutdown Plus
(FORCEON = GND,
FORCEOFF
= V
CC
)
Receiver Input Threshold to
INVALID
Output High
Receiver Input Threshold to
INVALID
Output Low
INVALID,
READY
Output Voltage Low
(MAX3224E–MAX3227E)
INVALID,
READY
Output Voltage High
(MAX3224E–MAX3227E)
Receiver Positive or Negative
Threshold to
INVALID
High
Receiver Positive or Negative
Threshold to
INVALID
Low
Receiver or Transmitter Edge to
Transmitters Enabled
t
INVH
t
INVL
t
WU
Figure 4a
Figure 4a
Positive threshold
Negative threshold
-2.7
-0.3
+0.3
2.7
V
V
Transmitter Output Voltage
ESD PROTECTION
±5
V
±15
±8
±15
kV
I
OUT
= -1.6mA
0.4
V
I
OUT
= -1.0mA
V
CC
- 0.6
V
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 5b (Note 2)
15
1
30
100
30
60
µs
µs
µs
s
Receiver or Transmitter Edge to
t
AUTOSHDN
V
CC
= 5V, Figure 5b (Note 2)
Transmitters Shutdown
Maxim Integrated
3
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
TIMING CHARACTERISTICS—MAX3224E/MAX3226E/MAX3244E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Maximum Data Rate
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3244E only)
Normal operation (MAX3244E only)
(Note 3)
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ,
measured from +3V to -3V
or -3V to +3V, one trans-
mitter switching
MIN
250
0.15
0.15
200
200
100
50
C
L
= 150pF
to 1000pF
TYP
MAX
UNITS
kbps
µs
ns
ns
ns
ns
Transition-Region Slew Rate
6
30
V/µs
TIMING CHARACTERISTICS—MAX3225E/MAX3227E/MAX3245E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
Maximum Data Rate
V
CC
= 3.0V to 4.5V, R
L
= 3kΩ,
C
L
= 250pF, one transmitter switching
V
CC
= 4.5V to 5.5V, R
L
= 3kΩ,
C
L
= 1000pF, one transmitter switching
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3245E only)
Normal operation (MAX3245E only)
(Note 3)
MIN
250
1000
1000
0.15
0.15
200
200
25
50
µs
ns
ns
ns
ns
V/µs
kbps
TYP
MAX
UNITS
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ, C
L
= 150pF to 1000pF,
Transition-Region Slew Rate
24
150
measured from +3V to -3V or -3V to +3V,
one transmitter switching
Note 2:
A transmitter/receiver edge is defined as a transition through the transmitter/receiver input logic thresholds.
Note 3:
Transmitter skew is measured at the transmitter zero cross points.
This application report discusses the design of an RC-based capacitive single-touch sensor using an MSP430 microcontroller. The MSP430 has some unique features that make it ideal for interfacing with ...
Although some users are concerned about the series operation of power supplies, this is a common phenomenon in industry use. The advantage is that the finished power supply can obtain a voltage of mor...
The video compression coding standard H.264/AVC was developed by the Joint Video Experts Group (JVT) composed of ISO/IEC and ITU-T. It introduced a series of advanced video coding technologies, such a...
[b][backcolor=white] [/backcolor][/b][align=left][color=rgb(0, 0, 0)][font=宋体][size=16px]Although transient analysis and steady-state analysis are two different methods, they are intrinsically linked....
//Can any expert help me interpret this code? NTSTATUS CDeviceBoardIWI::SetToMode(ULONG Mode) { if(GetCurrentMode() == Mode) return STATUS_SUCCESS; NTSTATUS Status = STATUS_SUCCESS; switch(Mode) { cas...
I have had the development board kit for a while, but due to work reasons, I only started writing development routines today.
The development and application of ESP32-S2-Kaluga-1 is divided into the f...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Don’t just look at the power when choosing a power supply
We know that a power supply with a low rated power can hardly meet the power supply needs of the system, which may cause frequent free...[Details]
Power supply is often the most easily overlooked link in the circuit design process. In fact, as an excellent design, power supply design should be very important, which greatly affects the perfor...[Details]
1 Introduction
At present, people have higher and higher requirements for the quality of life. When people are busy with work, soymilk machine is a new type of household beverage machine. It uses so...[Details]
DigRF
is
poised to replace the two main forms of data communication paths between RF and baseband semiconductor devices:
analog
signaling, and proprietary digital signaling (paralle...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
introduction
The air compressor unit in the operating area of a lead-zinc mine in Guangdong is a key equipment in mining production. There are six imported Ingersoll Rand CENTAC air compress...[Details]
If users want to extend the effective use time of the battery, in addition to ensuring the quality of the charger, correct charging techniques are also essential. Here are 14 tips for charging mobile ...[Details]
1 Introduction
In order to cope with the energy crisis and slow down global warming, many countries have begun to pay attention to energy conservation and emission reduction and the de...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
