Data sheet No. PD60280
IPS6021(
S
)(
R
)PbF
INTELLIGENT POWER HIGH SIDE SWITCH
Features
•
•
•
•
•
•
•
•
•
Over temperature shutdown (with auto-restart)
Short circuit protection (current limit)
Reverse battery protection (turns On the MOSFET)
Full diagnostic capability (short circuit to battery)
Active clamp
Open load detection in On and Off state
Ground loss protection
Logic ground isolated from power ground
ESD protection
Product Summary
Rds(on)
Vclamp
I Limit
Open load
Packages
30mΩ max.
39V
32A
3V / 1.1A
Description
The IPS6021(S)(R)PbF is a five terminal Intelligent Power
Switch (IPS) for use in a high side configuration. It features
short circuit, over-temperature, ESD protection, inductive
load capability and diagnostic feedback. The output
current is limited to the Ilim value. The current limitation is
activated until the thermal protection acts. The over-
temperature protection turns off the device if the junction
temperature exceeds the Tshutdown value. It will
automatically restart after the junction has cooled 7°C
below the Tshutdown value. The reverse battery
protection turns On the MOSFET. A diagnostic pin
provides different voltage levels for each fault condition.
The double level shifter circuitry will allow large offsets
between the logic and load ground.
TO-220
IPS6021PbF
D²Pak
D-Pak
IPS6021SPbF IPS6021RPbF
Typical Connection
+5V
+Bat
Rdgp
Vcc(3)
Dg(4)
Control
Rdgs
Pull-up resistors required for
open load off and short
circuit to Vbat detection
In(2)
V Diag
Rin
Gnd(1)
Out(5)
Input Signal
Load
www.irf.com
1
IPS6021(
S
)(
R
)PbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are referenced to Ground lead. (Tambient=25°C unless otherwise specified).
Symbol
Vout
Voffset
Vin
Vcc max.
Vcc cont.
Vcc sc.
Iin max.
Idg max.
Vdg
Pd
Parameter
Maximum output voltage
Maximum logic ground to load ground offset
Maximum input voltage
Maximum Vcc voltage
Maximum continuous Vcc voltage
Maximum Vcc voltage with short circuit protection
Maximum IN current
Maximum diagnostic output current
Maximum diagnostic output voltage
Maximum power dissipation (internally limited by thermal protection)
Rth=5°C/W IPS6021
Rth=40°C/W IPS6021S 1”sqrt. footprint
Rth=50°C/W IPS6021R 1”sqrt. footprint
Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω
Between In and Vcc
Other combinations
Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH
Between In and Vcc
Other combinations
Max. storage & operating temperature junction temperature
Soldering temperature (10 seconds)
Min.
Max.
Units
Vcc-35 Vcc+0.3
Vcc-35 Vcc+0.3
-0.3
5.5
⎯
36
⎯
28
⎯
28
-3
10
-3
10
-0.3
5.5
⎯
⎯
⎯
⎯
⎯
⎯
⎯
V
mA
V
W
25
3.1
2.5
1500
4000
100
500
150
300
ESD
V
Tj max.
Tsoldering
-40
⎯
°C
°C
Thermal Characteristics
Symbol
Rth1
Rth2
Rth1
Rth2
Rth3
Rth1
Rth2
Rth3
Parameter
Thermal resistance junction to ambient IPS6021 TO220 free air
Thermal resistance junction to case IPS6021 TO220
Thermal resistance junction to ambient IPS6021S D²Pak std. footprint
Thermal resistance junction to ambient IPS6021S D²Pak 1” sqrt. footprint
Thermal resistance junction to case IPS6021S D²Pak
Thermal resistance junction to ambient IPS6021R D-Pak std. footprint
Thermal resistance junction to ambient IPS6021R D-Pak 1” sqrt. footprint
Thermal resistance junction to case IPS6021R D-Pak
Typ.
50
2.6
60
40
2.6
70
50
2.6
Max.
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
Units
°C/W
Recommended Operating Conditions
These values are given for a quick design. For operation outside these conditions, please consult the application notes.
Symbol
VIH
VIL
Iout
Parameter
High level input voltage
Low level input voltage
Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V
Rth=5°C/W IPS6021
Rth=40°C/W IPS6021S 1” sqrt. footprint
Rth=50°C/W IPS6021R 1” sqrt. footprint
Recommended resistor in series with IN pin
Recommended resistor in series with DG pin for reverse battery protection
Recommended pull-up resistor for DG
Recommended pull-up resistor for open load detection
Max. switching frequency
Min.
4
0
⎯
⎯
⎯
Max.
5.5
0.9
12
4.3
3.9
10
20
20
100
1.5
Units
A
Rin
Rdgs
Rdgp
Rol
F max.
4
4
4
5
⎯
kΩ
kHz
2
www.irf.com
IPS6021(
S
)(
R
)PbF
Static Electrical Characteristics
Tj=25°C, Vcc=14V (unless otherwise specified)
Symbol
Rds(on)
Parameter
ON state resistance Tj=25°C
ON state resistance Tj=150°C
ON state resistance Tj=25°C, Vcc=6V
ON state resistance during reverse battery
Operating voltage range with short circuit
protection
Vcc to Out clamp voltage 1
Vcc to Out clamp voltage 2
Supply current when Off
Supply current when On
Input high threshold voltage
Input low threshold voltage
Input hysteresis
Input current when device is On
Dg leakage current
Low level DG voltage
Min.
⎯
⎯
⎯
⎯
Typ.
24
42
29
31
⎯
Max.
30
52
36
39
28
⎯
Units
mΩ
Test Conditions
Vin=5V, Iout=10A
Vin=5V, Iout=10A
Vin=5V, Iout=5A
Vcc-Gnd=14V
Vcc op.
V clamp 1
V clamp 2
Icc Off
Icc On
Vih
Vil
In hyst.
Iin On
Idg
Vdg
6
37
⎯
⎯
⎯
⎯
1.5
0.2
⎯
⎯
⎯
39
40
4
2.2
2.5
2
0.5
40
0.1
0.25
V
µA
mA
V
µA
V
42
9
5
2.9
⎯
Iout=40mA
Iout=8A (see Fig. 1)
Vin=0V, Vout=0V
Vin=5V
1
100
10
0.4
Vin=5V
Vdg=5V
Idg=1.6mA
Switching Electrical Characteristics
Vcc=14V, Resistive load=6Ω, Vin=5V, Tj=25°C
Symbol
Tdon
Tr1
Tr2
dV/dt (On)
EOn
Tdoff
Tf
dV/dt (Off)
EOff
Parameter
Turn-on delay time
Rise time to Vout=Vcc-5V
Rise time to Vout=0.9 x Vcc
Turn On dV/dt
Turn On energy
Turn-off delay time
Fall time to Vout=0.1 x Vcc
Turn Off dV/dt
Turn Off energy
Min.
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
Typ.
14
10
18
0.8
250
40
15
1.5
100
Max.
28
28
50
1.5
⎯
Units
µs
V/µs
µJ
µs
V/µs
µJ
Test Conditions
see Fig. 3
70
45
4.5
⎯
www.irf.com
3
IPS6021(
S
)(
R
)PbF
Protection Characteristics
Symbol
Ilim
Tsd+
Tsd-
Vsc
UV
UV hyst.
VOL Off
I OL On
Parameter
Internal current limit
Over temperature high threshold
Over temperature low threshold
Short-circuit detection voltage(2)
Min.
19
150(1)
⎯
Typ.
32
165
158
3
5
⎯
Max.
50
⎯
⎯
Units
A
°C
Test Conditions
Vout=0V
See fig. 2
2
⎯
Open load detection threshold
Open load detection threshold
0.25
2
0.3
3
0.7
4
5.9
1.6
4
1.1
V
A
(1) Guaranteed by design
(2) Reference to Vcc
True Table
Operating Conditions
IN
OUT
DG
Normal
H
H
H
Normal
L
L
H
Open Load
H
H
L
Open Load (3)
L
H
L
Short circuit to Gnd
H
L
L
Short circuit to Gnd
L
L
H
Short circuit to Vcc
H
H
L (4)
Short circuit to Vcc (5)
L
H
L
Over-temperature
H
L
L
Over-temperature
L
L
H
(3) With a pull-up resistor connected between the output and Vcc.
(4) Vds lower than 10mV.
(5) Without a pull-up resistor connected between the output and Vcc.
Lead Assignments
3- Vcc
3- Vcc
1- Gnd
2- In
3- Vcc
4- Dg
5- Out
12345
D²Pak – D Pak
1 2 3 4 5
TO220
www.irf.com
4
IPS6021(
S
)(
R
)PbF
Functional Block Diagram
All values are typical
VCC
165°C
Tj
43V
158°C
Vcc-gnd >UV
2.5V
Level
Shifter
Charge
Pump
37V
Driver
43V
IN
6V
150k
Ω
2.0V
-
Over-temp
Open load off
+
I Limit
+
-
I sense
DG
6V
Short circuit
3V
-
+
3V
Open load on
Ground
Disconnect
-
+
20mV
GND
OUT
www.irf.com
5
京公网安备 11010802033920号
EEWORLD
