EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B24B0SWI

Description
Fixed Resistor, Thin Film, 0.25W, 24000ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B24B0SWI Overview

Fixed Resistor, Thin Film, 0.25W, 24000ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP

D55342E07B24B0SWI Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145080723382
package instructionCHIP
Reach Compliance Codenot_compliant
ECCN codeEAR99
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance24000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
D
D
3
3
3D Models
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-55 °C to +150 °C
-55 °C to +150 °C
< - 25 dB
R
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 14-May-2020
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
What is the difference between Tx and INTX in the attached picture?
What is the difference between Tx and INTX marked by red arrows in the figure below? Does the dashed line above INTX mean that the voltage coming from INTX is low?...
一沙一世 51mcu
I am planning to DIY a learning version with VGA display function~~~Can anyone give me some suggestions?
As the title says, I am planning to DIY a MCU learning board with VGA display function. I would like to hear your suggestions on how to determine the function....
soso MCU
Why are many gate circuits reversed?
Many components like to use NAND gates and NOR gates, so that the input and output are inverted. It feels very troublesome. Is there any reason for this?...
kevinliu Embedded System
STM32L476 serial port interrupt function cannot use UART5_IRQHandler
The solution this time is actually mainly my problem: macro definition #define USART_USB_IRQHandler UART5_IRQHandler in uart.h In uart.c file void USART_USB_IRQHandler (void) { HAL_UART_IRQHandler(&Ua...
2638823746 stm32/stm8
Very strange problem - STM8S105S6 program cannot be burned into
The specific situation is as follows: Option BYTE and Data Memory can be programmed separately, so the wiring error problem is ruled out. But the Program Memory cannot be burned. The message is: faile...
威海 佟 stm32/stm8
I want to use the MSP-EXP430FR5739 experimental board to make an electric car meter
I want to use the MSP-EXP430FR5739 experimental board to make an electric car meter, and I want to make a preliminary plan for the functions. 1. Mileage calculation 2. Speed calculation 3. Voltage and...
wlmwwx Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1924  2881  2521  2102  801  39  59  51  43  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号