EEWORLDEEWORLDEEWORLD

Part Number

Search

HCPL-4503-360E

Description
high speed optocouplers 1mbd 1ch 16ma
CategoryLED optoelectronic/LED    photoelectric   
File Size320KB,16 Pages
ManufacturerAVAGO
Websitehttp://www.avagotech.com/
Environmental Compliance
Download Datasheet Parametric View All

HCPL-4503-360E Online Shopping

Suppliers Part Number Price MOQ In stock  
HCPL-4503-360E - - View Buy Now

HCPL-4503-360E Overview

high speed optocouplers 1mbd 1ch 16ma

HCPL-4503-360E Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAVAGO
package instruction0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8
Reach Compliance Codecompliant
ECCN codeEAR99
Factory Lead Time17 weeks
Other featuresTTL COMPATIBLE, UL RECOGNIZED, VDE APPROVED
ConfigurationSINGLE
Current transmission ratio - minimum value19%
Nominal data rate1 MBps
Maximum forward current0.025 A
Maximum forward voltage1.8 V
Maximum insulation voltage3750 V
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of components1
Maximum on-state current0.008 A
Maximum operating temperature100 °C
Minimum operating temperature-55 °C
Optoelectronic device typesLOGIC IC OUTPUT OPTOCOUPLER
Maximum power dissipation0.1 W
surface mountYES
Terminal surfaceMatte Tin (Sn)
Base Number Matches1
HCNW4502/3
HCPL-0452/0453/4502/4503
Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
These diode-transistor optocouplers use an insulating
layer between a LED and an integrated photodetector to
provide electrical insulation between input and output.
Separate connections for the photodiode bias and out-
put-transistor collector increase the speed up to a hun-
dred times that of a conventional phototransistor coupler
by reducing the base-collector capacitance.
These single channel optocouplers are available in
8-Pin DIP, SO-8 and Widebody package configurations.
The HCPL-4502/4503 and HCNW4502/4503 are designed
for high speed TTL/TTL applications. A standard 16 mA TTL
sink current through the input LED will provide enough
output current for 1 TTL load and a 5.6 kΩ pull-up resistor.
CTR for these devices is 19% minimum at I
F
= 16 mA.
Features
15 kV/µs minimum common mode transient
immunity at V
CM
= 1500 V
High speed: 1 Mb/s
TTL compatible
Available in 8-Pin DIP, SO-8, widebody packages
Open collector output
Guaranteed performance from temperature:
0°C to 70°C
Safety approval
UL Recognized – 3750 V
rms
for 1 minute (5000 V
rms
for 1 minute for HCNW and Option 020 devices)
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-5 Approved
– V
IORM
= 630 V peak for HCPL-4503#060
– V
IORM
= 1414 V peak for HCNW devices
Dual channel version available (4534/0534)
MIL-PRF-38534 hermetic version available
(55XX/65XX/4N55)
Functional Diagram
NC 1
ANODE 2
CATHODE 3
NC 4
8 V
CC
7 NC
6 V
o
5 GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
V
o
ON
LOW
OFF
HIGH
Applications
High voltage insulation
Video signal isolation
Power transistor isolation in motor drives
Line receivers
Feedback element in switched mode power supplies
High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL
Replaces pulse transformers
Replaces slow phototransistor isolators
Analog signal ground isolation
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION:
It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
EEWORLD University Hall - A Week of Learning Series - Analog Electronics
Mastering Analog Electronics in One Week : https://training.eeworld.com.cn/course/3939...
老白菜 Analog electronics
How to display the receiving address using 12864?
For example, a frame of received data is stored in the array rx[]={0x87,0x81,0x82,0x83,0x84,0x85}. How can I display it using the 12864 LCD? The display effect is: 87 81 82 83, etc. In the past, it wa...
chenxiang1 51mcu
Share the programming example of TI microcontroller MSP430-FLASH information area
[list=1] [*][color=#483d8b]2.void flash_clr(int *ptr) [/color] [*][color=#483d8b]3.{ [/color] [*][color=#483d8b]4. _DINT(); //Disable interrupt[/color] [*][color=#483d8b]5. FCTL3 = 0x0A500; //* Lock =...
Jacktang Microcontroller MCU
Which gear should I use to measure the serial port signal with a multimeter?
Since the serial port signal is a pulse signal, that is, it belongs to AC, why do we use the DC range to measure it? Is the value measured by the DC range an effective value? Can we use the AC range t...
knife Embedded System
January 16, 2010, Seminar on Embedded System Hardware and Software Development Based on ARM (Beijing)
[color=#000000][color=#008000][color=#ff6600][font=Verdana]As the creator of the global RISC standard, ARM's dominant position in the field of embedded processors has long been recognized by everyone....
bjfarsighttop ARM Technology
Confusion about TFT LCD interface
A TFT LCD, driver chip ST7735, the microcontroller can be connected to 5V or 3.3V power supply. When using 3.3V, the LCD pins use resistors to divide the voltage to get 3V level, the LCD displays norm...
飞絮 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 823  1307  467  2702  2521  17  27  10  55  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号