EEWORLDEEWORLDEEWORLD

Part Number

Search

3199BA183U025MPA1

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 75% +Tol, 10% -Tol, 18000uF, Stud Mount, CAN, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size144KB,6 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance  
Download Datasheet Parametric View All

3199BA183U025MPA1 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 75% +Tol, 10% -Tol, 18000uF, Stud Mount, CAN, ROHS COMPLIANT

3199BA183U025MPA1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1594666581
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance18000 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter35.41 mm
dielectric materialsALUMINUM (WET)
ESR24.8 mΩ
length54.81 mm
Manufacturer's serial number3199
Installation featuresSTUD MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
Package shapeCYLINDRICAL PACKAGE
Package formScrew Ends
polarityPOLARIZED
positive tolerance75%
Rated (DC) voltage (URdc)25 V
ripple current5000 mA
series3199
surface mountNO
Terminal pitch12.7 mm
Terminal shapeBINDING POST
Type 3199 Aluminum Electrolytic, Screw Terminals
Screw Terminal Capacitors for Power Output Filtering
With twice the capacitance of Type 3191 capacitor, Type 3199
extends output filtering performance into higher power,
especially with cold temperature requirements. Standard
encasement is with the capacitor element compressed onto
an aluminum peg in the can bottom and a phenolic peg in
the top. Optional Rilled construction is available. With rilled
construction the element is secured by rills, spoon shaped
dimples in the side of the can. Rilled construction offers
the industries highest vibration and shock withstanding
capability and excellent heat transfer.
Highlights
- Stud mount available
- High current application
- Industrial applications
- Smoothing and filtering
- Audio power supplies
–55 ºC to +85 ºC
7.5 Vdc to 75 Vdc
3900 µF to 1.2 F
–10% +30%
–10% +50%
≤6√CV µA (6 mA max.) at 5 minutes
Ambient Temperature
45 °C
2.24
Frequency
60 Hz 120 Hz
16 – 100 V
Low Temperature Characteristics
0.90
1.00
300 Hz
1.05
1000 Hz
1.10
≥10
kHz
1.15
55 °C
2.00
65 °C
1.73
75 °C
1.41
85 °C
1.00
Specifications
Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Ripple Current Multipliers
Impedance ratio: Z
–20⁰C
∕ Z
+25⁰C
≤ 8 (16–50 Vdc)
≤ 4 (63–75Vdc)
Endurance, 5000 h at rated voltage and 85 ºC
Δ Capacitance: ±10%
ESR ≤ 200% of limit
DCL ≤ 100% of limit
Storage, 500 h at 85 ºC
Δ Capacitance: ±10%
ESR ≤ 175% of limit
DCL ≤ 200% of limit
10 to 500 Hz, 0.75 mm or 10 g* if less, 3 directions, 2 h ea
Δ Capacitance: ±5%
no visible damage or leakage
*15 g if rilled construction
RoHS Compliant
Endurance Life Test
Shelf Life Test
Vibration
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
I am a novice and have just started to work with AD. I would like to ask about the library packaging and transplantation issues?
I'm a newbie. I just started to use AD and encountered some minor problems. The book I bought has some scattered device diagrams and schematics. I want to organize them and make a library, but I can't...
小小的人丶 PCB Design
About the problem of SPI clock not output
Does SPI have a clock signal as long as it sends data? Now there is data sent out, but there is no clock signal output. I have set it up like this: master mode, SDO controlled by the module, 8-bit tra...
明月清风 Embedded System
Ask about the CAN communication between two 2407 chips
There are two 2407 chips on a board, 5cm apart. If I directly cross-connect the CAN transceiver interface, is it feasible? Do I need 82C50 between them? I have used SPI and SCI, and I want to try CAN....
niantianxia Microcontroller MCU
On the selection of single chip microcomputer for oscilloscope
Regarding the dynamic display of the oscilloscope, to display a 10M bandwidth, no evaluation rate is required, no other processing is required, just sample and display the waveform. So can a crystal o...
dyh420 DIY/Open Source Hardware
MSP430 JTAG interface and BSW interface
1. JTAG port, JTAG pins are defined as follows:MCU TCK - test clock input, connected to the emulator's 7-pinMCU TDI - test data input, connected to the emulator's 2-pinMCU TDO - test data output, conn...
火辣西米秀 Microcontroller MCU
Take you to the STM32 starting point (a core developed specifically for embedded applications)
STM32 has been very popular recently, so let’s learn about STM32 together! 1. JLINK download program;2. IAR user guide and running light experiments;3. Button + buzzer program;[b][color=red]STM32 data...
njlianjian stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2502  380  2061  2150  4  51  8  42  44  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号