EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3QV01LG-1103CD

Description
LVPECL Output Clock Oscillator
CategoryPassive components    oscillator   
File Size229KB,22 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N3QV01LG-1103CD Overview

LVPECL Output Clock Oscillator

8N3QV01LG-1103CD Parametric

Parameter NameAttribute value
MakerIDT (Integrated Device Technology)
Reach Compliance Codecompli
Manufacturer's serial numberIDT8N3QV01
Oscillator typeLVPECL
Base Number Matches1
Quad-Frequency Programmable
VCXO
IDT8N3QV01 Rev G
DATA SHEET
General Description
The IDT8N3QV01 is a Quad-Frequency Programmable VCXO with
very flexible frequency and pull-range programming capabilities.
The device uses IDT’s fourth generation FemtoClock® NG
technology for an optimum of high clock frequency and low phase
noise performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 10-lead Ceramic 5mm x
7mm x 1.55mm package.
Besides the 4 default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N3QV01 can be programmed via the I
2
C
interface to any output clock frequency between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷N (N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to 4
independent PLL M and N divider registers (P, MINT, MFRAC and
N), reprogramming those registers to other frequencies under
control of FSEL0 and FSEL1 is supported. The extended
temperature range supports wireless infrastructure, tele-
communication and networking end equipment requirements. The
device is a member of the high-performance clock family from IDT.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), reprogrammable by I
2
C
I
2
C programming interface for the output clock frequency, APR
and internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
Absolute pull-range (APR) programmable from ±4.5 to
±754.5ppm
One 2.5V or 3.3V LVPECL differential clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz):
0.487ps (typical)
RMS phase jitter @ 156.25MHz (1kHz - 40MHz):
0.614ps (typical)
2.5V or 3.3V supply voltage modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
114.285 MHz
÷MINT,
MFRAC
2
VC
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
SDATA
SCLK
10
VC 1
OE 2
V
EE
3
4
FSEL0
9
8
7
V
CC
nQ
Q
5
6
A/D
7
25
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
7
IDT8N3QV01 Rev G
10-lead Ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N3QV01GCD REVISION A
FEBRUARY 24, 2012
1
©2012 Integrated Device Technology, Inc.
FSEL1
Does anyone have the routine for balancing a ball? It's a ping-pong ball sliding on a round flat surface and never falling off.
Does anyone have the routine for the ball balance? It's a ping-pong ball sliding on a round plate and never falling off~ Or his program idea is also fine~...
hd666666 PCB Design
Where can I download the firmware library for direct drive TFT?
Moderator:Hello, I have been using STM32F for some time and feel that STM32 has a high cost-effectiveness. Recently, I have been learning about the use of FSMC to drive the RGB interface. I downloaded...
wangdian2010 stm32/stm8
micropython update: 2020.5
Updated May 2020py/parse: Support constant folding of power operator for integers. esp32/partitions: Update comments in files regarding offset. esp32: Improve support for OTA updates. docs/library: Fi...
dcexpert MicroPython Open Source section
Does anyone have Chinese information about the NEC-78KOS series? Upload it.
Can anyone upload some Chinese information about the NEC-78KO series? Thanks....
xjc603 MCU
ZigBee Help!
I have just started to learn ZigBee. I have only read APL and NWKL briefly, and I have not read IEEE802.15.4. I use TI's Z-stack for protocol stack. I have done networking test and positioning test. B...
macheng80 Embedded System
VB programming RS232 serial port control stepper motor
After the host computer (PC or other control equipment with serial port) is connected to this control board through RS232 serial port, a string of ASCII code instructions can be sent to the control bo...
lyxmmk Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1482  709  1386  2393  1737  30  15  28  49  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号