EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11505212BALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11505212BALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-11505212BALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
Is SamacsysN
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
body length8.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
Base Number Matches1
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
LM3S9B95 program cannot be downloaded
IAR for ARM 6.10, J-Link emulator 4.22b, LM3S9B95 C5 version chip. The hardware diagram is attached. The error message is AHBID error? I really don't understand. The emulator is fine, even a 9B96 boar...
ultrabenz Microcontroller MCU
Disassembly of small reduction motor
[align=center][b][font=宋体][size=14.0pt]Disassembly of small reduction motor[/size][/font][/b][/align][align=center]DIY&Sharing—GravityShare[/align][align=center][align=center][font=宋体][size=12.0pt][hr...
万有引力平台 DIY/Open Source Hardware
How to output Gerber files for 4-layer boards in AltiumDesigner
[i=s]This post was last edited by littleshrimp on 2016-12-19 19:14[/i] GP1 and GP2 here are negative films, do they need special settings?In the generated gerber file, I see that the middle electrical...
littleshrimp PCB Design
Why does the resolution decrease when the gain is increased?
Why does the resolution decrease when the gain is increased?...
QWE4562009 Integrated technical exchanges
Learning "Introduction to Linux Drivers"
1. What does a typical Linux driver code include? Driver registration and deregistration, device opening and release, device reading and writing, device control operations, device interruption or poll...
vlonson Linux and Android
Evaluation of the domestic FPGA Gaoyun GW1N-4 series development board - Software Part 2
For simple designs, for physical constraints we may only need to bind the pins and levels, and for timing constraints we only need to constrain the main clock to meet the design and timing requirement...
打破传统 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1514  735  1603  1427  513  31  15  33  29  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号