EEWORLDEEWORLDEEWORLD

Part Number

Search

1-862551-0

Description
LGH-1L SGL. MOLDED END LEAD
CategoryThe connector    The connector   
File Size280KB,6 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

1-862551-0 Overview

LGH-1L SGL. MOLDED END LEAD

1-862551-0 Parametric

Parameter NameAttribute value
Brand NameAMP
Is it Rohs certified?conform to
Objectid1826484940
Reach Compliance Codeunknown
YTEOL0
Back shell typeSOLID
Connector typeCIRCULAR CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderFEMALE
Contact materialNOT SPECIFIED
Contact styleRND PIN-SKT
DIN complianceNO
Electromagnetic interference shieldingNO
empty shellYES
Filter functionNO
IEC complianceNO
MIL complianceNO
Power Connector Ratings115/230VAC
Mixed contactsNO
Installation typeCABLE
Number of connectorsONE
Number of ports1
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
OptionsGENERAL PURPOSE
Panel mountingNO
Rated voltage25000 V
Total number of contacts1
Maximum wire diameter16 AWG
Design
Objectives
Standard LGH Connectors,
Series 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I
108-36033
Rev O2
DESIGN OBJECTIVES
The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore
Tyco Electronics makes no representation or warranty, express or implied, that the product will comply with these requirements. Further,
Tyco Electronics may change these requirements based on the results of additional testing and evaluation. Contact Tyco Electronics
Engineering for further details.
1.
1.1.
SCOPE
Content
This specification covers perform ance, tests and quality requirem ents for the Tyco Electronics LGH
standard high voltage 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I series m olded end leads and receptacles. These
leads and receptacles are designed for com m ercial, industrial and m ilitary type applications requiring
operation over wide environm ents.
1.2.
Qualification
W hen tests are perform ed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be perform ed using the applicable inspection plan and product drawing.
2.
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and the referenced docum ents,
this specification shall take precedence.
2.1.
Tyco Electronics Docum ents
!
!
!
!
109 Series: Test Specifications as indicated in Figure 1
109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods)
114- : Application Specification
501- : Qualification Test Report
2.2.
Com m ercial Standard
EIA-364:
Electrical Connector/Socket Test Procedures Including Environm ental Classifications
2.3.
Military Standard
MIL-STD-202: Test Methods For Electronic And Electrical Com ponent Parts
3.
3.1.
REQUIREM ENTS
Product shall be of the design, construction and physical dim ensions specified on the applicable product
drawing.
©2011 Tyco Electronics Corporation, | Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
1 of 6
LOC B
DESIGN OBJECTIVES
Design and Construction
DESIGN OBJECTIVES 07 Mar 11
Ten Commandments of Good Design
The money is not enough again, and new content is released...
netkernel Analog electronics
[MSP430 Fun Talk] MSP430 Lecture 4: A Brief Talk on Interrupts
[align=center][font=微软雅黑][size=4]MSP430 Tutorial 4[/size][/font][/align][align=left][font=微软雅黑][size=4] Last time I talked with you about the use of GPIO, but it was not very comprehensive. If it were...
michael_llh Microcontroller MCU
A computer collects data from n data sources in time-sharing mode and sends them to the main memory, and then processes them in time-sharing mode. When collecting data, the best method is to use
A computer collects data from n data sources in time-sharing mode and sends them to main memory, and then processes them in time-sharing mode. When collecting data, the best method is to use ___. A. s...
LQ77630 Embedded System
Does anyone know about the company Shenzhen Haoke?
Does anyone know about Shenzhen Haoke? It seems to be specialized in WINCE products, but I can't find any information about it online. Is it a newly started company? Please share more....
amzip Embedded System
Digital Control Implementation of Switching Power Supply
Although many in the industry believe that analog and digital technologies will soon compete for dominance in the control circuits of power regulation devices, the reality is that the two technologies...
Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2851  1609  1618  2305  2754  58  33  47  56  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号