EEWORLDEEWORLDEEWORLD

Part Number

Search

1658619-6

Description
ULTRA NOVO RCP CTR&ML GRY 15AU
CategoryThe connector    The connector   
File Size178KB,5 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

1658619-6 Overview

ULTRA NOVO RCP CTR&ML GRY 15AU

1658619-6 Parametric

Parameter NameAttribute value
Brand NameAMP
Is it Rohs certified?conform to
MakerTE Connectivity
Reach Compliance Codecompliant
Is SamacsysN
Connector typeBOARD CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact materialNOT SPECIFIED
Base Number Matches1
Product
Specification
108-1740
09Aug05 Rev D
Receptacle, AMP-LATCH* Ultra Novo, Flat Cable Round
Conductor
1.
1.1.
SCOPE
Content
This specification covers performance, tests and quality requirements for the AMP-LATCH* Ultra Novo
flat cable round conductor connector receptacles. Receptacle contacts are crimped to 0.635 mm [.025
in] centerline ribbon cable conductors (30 AWG solid and stranded). Complete assemblies mate to
0.635 mm [.025 in] square posts on 2.54 mm [.100 in] centerline with equivalent post length of 5.33 ±
.089 mm [.210 ± .035 in].
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
|
2.1.
Tyco Electronics Documents
109-1:
General Requirements for Test Specifications
109 Series:
Test Specifications as indicated in Figure 1
114-40056:
Application Specification
501-399: Qualification Test Report
|
|
|
3.
3.1.
Product shall be of the design, construction and physical dimensions specified on the applicable
product drawing.
3.2.
Materials
Contact: Copper alloy
Ground plate: Copper alloy
Housing: Thermoplastic, UL94V-0
©2005 Tyco Electronics Corporation
Harrisburg, PA
All International Rights Reserved.
!
!
!
!
!
!
!
REQUIREMENTS
Design and Construction
* Trademark
| Indicates change
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
1 of 5
LOC B
Heat dissipation calculation and heat sink selection for power devices
At present, electronic products mainly use SMD packaging devices, but many high-power devices and some power modules still use perforated packaging, which is mainly because they can be easily installe...
lixiaohai8211 Analog electronics
Important! WIFI-CC3200 Power Management Power Consumption Test Notes
[i=s]This post was last edited by hanskying666 on 2016-1-26 10:07[/i] I saw the CC3200 power supply test notes on deyisupport. The attached notes have detailed test pictures. If you have any questions...
hanskying666 Wireless Connectivity
【NXP Rapid IoT Review】W4 Bluetooth Review
[i=s]This post was last edited by johnrey on 2019-1-21 16:07[/i] [size=14px]Although the last round of sensor evaluation was not very smooth, and there are still many problems left unresolved, we fina...
johnrey RF/Wirelessly
EEWORLD University - Microsemi Fusion Series FPGA Getting Started Guide
Microsemi Fusion Series FPGA Getting Started Guide : https://training.eeworld.com.cn/course/565...
FPGAfans2015 FPGA/CPLD
Dormitory intelligent anti-theft and fire alarm system based on WT588D
Dormitory intelligent anti-theft and fire alarm system based on WT588D summary: This design uses the ultra-low power single-chip MSP430F149 as the control core to realize the intelligent anti-theft an...
iushiyuan Energy Infrastructure?
Transistor problem
A signal of about 8M passes through C11 and the transistor. The 8M signal is generated by a capacitor three-point oscillation circuit, passes through C11, and then is amplified by the transistor. How ...
S3S4S5S6 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2252  2886  1980  497  1370  46  59  40  10  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号