EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4QV01BG-0103CD

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size185KB,19 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4QV01BG-0103CD Overview

LVDS Output Clock Oscillator

8N4QV01BG-0103CD Parametric

Parameter NameAttribute value
MakerIDT (Integrated Device Technology)
Reach Compliance Codecompli
Oscillator typeLVDS
Base Number Matches1
Quad-Frequency Programmable
VCXO
IDT8N4QV01 REV G
DATA SHEET
General Description
The IDT8N4QV01 is a Quad-Frequency Programmable VCXO with
very flexible frequency and pull-range programming capabilities.
The device uses IDT’s fourth generation FemtoClock® NG
technology for an optimum of high clock frequency and low phase
noise performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 10-lead ceramic 5mm x
7mm x 1.55mm package.
Besides the 4 default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4QV01 can be programmed via the I
2
C
interface to any output clock frequency between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷N (N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to 4
independent PLL, P, M and N divider registers (P, MINT, MFRAC
and N), reprogramming those registers to other frequencies under
control of FSEL0 and FSEL1 is supported. The extended
temperature range supports wireless infrastructure, tele-
communication and networking end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency, APR
and internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
Absolute pull-range (APR) programmable from ±4.5ppm to
±754.5ppm
One 2.5V or 3.3V LVDS differential clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.494ps
(typical)
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.594ps
(typical)
2.5V or 3.3V supply voltage modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
114.285 MHz
÷MINT,
MFRAC
2
VC
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
VC 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
A/D
7
25
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
7
IDT8N4QV01 REV G DATA SHEET
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4QV01GCD
FEBRUARY 24, 2012
1
©2012 Integrated Device Technology, Inc.
RK2706 circuit diagram
RK2706 circuit diagram...
美目如初 Embedded System
ATX-100 Series Cable Harness Tester Revealed! (Demo + Features)
ATX-100 Series Cable Harness Tester Revealed! (Demo + Features)...
aigtekatdz Test/Measurement
Asking for advice - WinCE4.2 2440 board, serial port received data is easily lost!
I recently found out during debugging on the board that when the baud rate is 115200, the system receives external data, and when the amount of data is large, it is easy to lose! From the first lost d...
qijiguo99 Embedded System
Who can give me the control circuit of the car main driver's door glass lifting switch group
Who can give me a control circuit for the car's main driver's door window lift switch group? This switch communicates with the door module LIN. It is found that when there is no LIN signal from the do...
造个时光机器 Automotive Electronics
Please recommend a beginner video for learning STM32
Please recommend a beginner's video for learning STM32, or the code of teacher Li Xiang's video. Urgently needed, thank you...
hui4341 stm32/stm8
Sincerely ask for advice on intercepting the debug information output to the serial port by RETAILMSG
I want to intercept the debugging information that RETAMALMSG outputs to the serial port, save it in a file, and then display it on an interface I define. It's a bit similar to the function of DEBUGVI...
KESKY Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1771  1421  1505  2539  2918  36  29  31  52  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号