EEWORLDEEWORLDEEWORLD

Part Number

Search

10118615-404003LF

Description
Board Connector, 4 Contact(s), 1 Row(s), Male, Straight, Solder Terminal,
CategoryThe connector    The connector   
File Size264KB,4 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

10118615-404003LF Overview

Board Connector, 4 Contact(s), 1 Row(s), Male, Straight, Solder Terminal,

10118615-404003LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1237931590
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL9.1
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN (100) OVER NICKEL (50)
Contact completed and terminatedTin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee3
MIL complianceNO
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded1
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts4
PDS: Rev :E
STATUS:Released
Printed: Jul 22, 2014
Zhejiang University 2009 Electronic Competition Training Materials.rar
[i=s]This post was last edited by paulhyde on 2014-9-15 04:13[/i] Zhejiang University 2009 Electronic Competition Training Materials.rar...
dtcxn Electronics Design Contest
Question: STEPLDR reads FLASH block error?
I first burned STEPLDR.NB1 at block 0, and the serial port print output was normal after startup; but after burning eboot.nb0, an error message was printed: ECC ERROR block 0x00000002 page 0x00000000,...
请求权 Embedded System
SDRAM Control in VHDL
ALTERA IP core original code, SDRAM controller program, absolutely practical...
wenhuawu FPGA/CPLD
The answer to this question is wrong... right? I really don't understand why the answer is drawn like that!
The question is shown in Figure 1. I can't figure out why the answer is drawn like that. Only analyze the situation where Rw2 is at the top. The question shows a sawtooth wave generator. Because the s...
lllxxq141592654 Analog electronics
The problem of replacing the tuning circuit of the high-frequency head of the TV set
I have an old TV. The original tuning circuit is old and the tuning voltage is unstable. Later, I removed the original potentiometer and replaced it with a volume potentiometer. It worked well at firs...
qianfan Analog electronics
Why are point E and the midpoint of the load resistance equivalent to grounding?
[color=#000][font=Arial, SimSun]Since the potential of point E does not change under the action of differential mode signal, it is equivalent to being connected to the "ground"; and since the potentia...
beehive Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 832  2780  1585  689  398  17  56  32  14  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号