EEWORLDEEWORLDEEWORLD

Part Number

Search

D38999/30GG27HC

Description
MIL Series Connector, 27 Contact(s), Aluminum Alloy, Female, Crimp Terminal
CategoryThe connector    The connector   
File Size960KB,111 Pages
ManufacturerDefense Logistics Agency
Download Datasheet Parametric View All

D38999/30GG27HC Overview

MIL Series Connector, 27 Contact(s), Aluminum Alloy, Female, Crimp Terminal

D38999/30GG27HC Parametric

Parameter NameAttribute value
Objectid1129883454
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresSTANDARD: MIL-C 38999
Rear interface of connectorMIL-C-38999 Ser III,IV
Connector insertion detailsI202
Connector typeMIL SERIES CONNECTOR
Contact point genderFEMALE
Contact part numberM39029/56-351
Number of contacts27
Contact size20
Contact typeCrp Rear Rlse
Coupling typeTHREADED
other instructionsPlug, Lanyard Rlse
Drawing date and revision17DEC99,K
Environmental characteristicsENVIRONMENT RESISTANT
waterproof levelPartial
MIL complianceYES
Military connector housingS400B
Mixed contactsNO
Maximum operating temperature200 °C
Minimum operating temperature-65 °C
Maximum plug diameter1.642 inch
polarizationC
Shell surfaceELECTROLESS NICKEL
Shell materialALUMINUM ALLOY
Housing size21
Termination typeCRIMP
Total number of contacts27
Unique insertion numberG27
INCH-POUND
MIL-DTL-38999K
17 December 1999
SUPERSEDING
MIL-C-38999J
06 April 1990
DETAIL SPECIFICATION
CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY,
QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING),
ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS
GENERAL SPECIFICATION FOR
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
1. SCOPE
1.1 Scope. This specification covers four series of miniature, high density, bayonet, threaded, or breech
coupling, circular, environment resistant, electrical connectors using removable crimp or fixed hermetic
solder contacts, and are capable of operation within a temperature range of -65°C to +200°C (see 1.3.1d).
See 6.1 for intended use and applications.
1.2 Description. All series include rear release removable pin and socket contacts with crimp
termination. All series are designed to assure proper orientation of the mating halves prior to electrical
circuit closure. All series include hermetically sealed receptacles with fixed contacts for solder termination.
All series include EMI shielding capability. Series I, III, and IV connectors with conductive finishes provide
electrical continuity between mated shells prior to contact engagement and have the contacts so located as
to be protected from handling damage and inadvertent electrical contact. Series II provides low silhouette
for minimum size and weight and includes connectors which provide shell-to-shell electrical continuity when
mated.
1.3 Classification.
1.3.1 Connectors. Connectors fabricated to this specification are classified as follows:
a. Series: The series I, II, III, and IV connectors are not interchangeable or intermateable.
I
II
III
IV
-
-
-
-
Scoop-proof, bayonet coupling.
Non-scoop-proof, bayonet coupling, low silhouette.
Scoop-proof, triple start, self-locking, threaded coupling.
Scoop-proof, breech coupling.
Beneficial comments (recommendations, additions, deletions) and any pertinent data which may
be of use in improving this document should be addressed to: Defense Supply Center Columbus,
ATTN: VAI, 3990 East Broad Street, Columbus OH 43216-5000 by using the self-address
Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this
document or by letter.
AMSC N/A
DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.
FSC 5935
I built a CCSV5 project myself, and after compiling it, I always get the following error
[b]I built a CCSV5 project by myself, and after compiling it, it always prompts the following error. I have checked a lot of information, but couldn't find a solution. Could you give me a solution and...
fyd1022 Microcontroller MCU
What is a diode used for?
What is the function of D17? Can it be removed? I feel it is useless...
aq1261101415 Analog electronics
The PCB design of the level measurement system based on the capacitance-to-digital converter AD7746 is in progress!
I'm tired of drawing! Let's record the process...
蓝雨夜 ADI Reference Circuit
Thank you for being with you for ten years. EEWORLD sends you blessings on its tenth anniversary
[align=left][url=https://bbs.eeworld.com.cn/huodong/eeworld_10_year/][b][size=3][color=#8b0000]Grateful for being with you for ten years, wishing you a happy 10th anniversary of EEWORLD[/color][/size]...
eric_wang Talking
Multisim 10.0 design of light-controlled alarm system has been solved
This has been solved. The light-controlled alarm system designed using Multisim 10.0.1, when the potentiometer R2 simulates the light dimming and the resistance value increases, the buzzer will sound,...
平淡最真 Analog electronics
Altera's signal generation program designed with IP core
[i=s] This post was last edited by paulhyde on 2014-9-15 09:24 [/i] Altera's signal generation program designed with IP core...
wangwei20060608 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2645  694  1829  2095  1290  54  14  37  43  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号