EEWORLDEEWORLDEEWORLD

Part Number

Search

DS26524GA5+

Description
network controller & processor ics 4-port E1/T1/J1 transceiver
CategoryWireless rf/communication    Telecom circuit   
File Size2MB,273 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Environmental Compliance
Download Datasheet Parametric View All

DS26524GA5+ Overview

network controller & processor ics 4-port E1/T1/J1 transceiver

DS26524GA5+ Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerMaxim
Reach Compliance Codecompli
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Telecom integrated circuit typesTIME SLOT 0/16 TRANSCEIVER
Maximum time at peak reflow temperatureNOT SPECIFIED
DS26524
Quad T1/E1/J1 Transceiver
www.maxim-ic.com
GENERAL DESCRIPTION
The DS26524 is a single-chip 4-port framer and line
interface unit (LIU) combination for T1, E1, and J1
applications. Each channel is independently
configurable, supporting both long-haul and short-haul
lines.
FEATURES
Four Complete T1, E1, or J1 Long-Haul/Short-
Haul Transceivers (LIU plus Framer)
Independent T1, E1, or J1 Selections for Each
Transceiver
Internal Software-Selectable Transmit- and
Receive-Side Termination for 100Ω T1 Twisted
Pair, 110Ω J1 Twisted Pair, 120Ω E1 Twisted
Pair, and 75Ω E1 Coaxial Applications
Crystal-Less Jitter Attenuator can be Selected
for Transmit or Receive Path; Jitter Attenuator
Meets ETS CTR 12/13, ITU-T G.736, G.742,
G.823, and AT&T Pub 62411
External Master Clock can be Multiple of
2.048MHz or 1.544MHz for T1/J1 or E1
Operation; This Clock is Internally Adapted for
T1 or E1 Usage in the Host Mode
Receive-Signal Level Indication from -2.5dB to
-36dB in T1 Mode and -2.5dB to -44dB in E1
Mode in Approximate 2.5dB Increments
Transmit Open- and Short-Circuit Detection
LIU LOS in Accordance with G.775, ETS 300
233, and T1.231
APPLICATIONS
Routers
Channel Service Units (CSUs)
Data Service Units (DSUs)
Muxes
Switches
Channel Banks
T1/E1 Test Equipment
TYPICAL OPERATING CIRCUIT
DS26524
T1/E1/J1
NETWORK
T1/J1/E1
Transceiver
x4
BACKPLANE
Transmit Synchronizer
Flexible Signaling Extraction and Insertion
Using Either the System Interface or
Microprocessor Port
Alarm Detection and Insertion
T1 Framing Formats of D4, SLC-96, and ESF
TDM
ORDERING INFORMATION
PART
DS26524G
DS26524G+
DS26524GN
DS26524GN+
TEMP RANGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
256 TE-CSBGA
256 TE-CSBGA
256 TE-CSBGA
256 TE-CSBGA
J1 Support
E1 G.704 and CRC-4 Multiframe
T1-to-E1 Conversion
Features Continued in Section
2.
+ Denotes lead-free/RoHS compliant device.
Note:
Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here:
www.maxim-ic.com/errata.
1 of 273
REV: 112907
School forum essence area information ~ electronic circuit design, experiment, test related, practical and easy to understand
[i=s] This post was last edited by paulhyde on 2014-9-15 04:01 [/i] Books on electronic circuit design, experiment and testing found in the electronic circuit section of the school forum are very help...
custom430 Electronics Design Contest
When downloading a program to a PCB board in SWD mode, what will happen if the PCB board's own power is not disconnected?
When downloading a program to a PCB board in SWD mode, what will happen if the PCB board's own power is not disconnected?...
深圳小花 MCU
DC005, soldering pad production of power plug (AD)
[b][color=#5E7384]This content is originally created by [size=3]TANG20051008[/size], a user of EEWORLD forum. If you want to reprint or use it for commercial purposes, you must obtain the author's con...
TANG20051008 PCB Design
A small problem after make
做的是led驱动,如下:[root@localhost root]# cd /working/boot/[root@localhost boot]# ls built-in.oled_driver.cMakefile[root@localhost boot]# make clean rm -rf *.o *~ core .depend .*.cmd *.ko *.mod.c .tmp_versio...
kly Embedded System
How did you first learn hardware design?
I am a newbie and haven't gotten started yet. Now I want to learn hardware, but I don't know where to start and what courses I should take. I hope you can give me some advice....
maojunwei123 Embedded System
How to set msp430 DCO
I want to use DCO to generate a 320K clock for SMCLK. I read the manual but didn't understand how to set it. What are the 8 discrete frequencies mentioned in the manual? Can anyone tell me how to set ...
han0602 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2359  2706  2880  2464  448  48  55  58  50  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号