EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342H12B30G0MT1

Description
RESISTOR, THIN FILM, 0.1 W, 2 %, 50 ppm, 30 ohm, SURFACE MOUNT, 0603, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342H12B30G0MT1 Overview

RESISTOR, THIN FILM, 0.1 W, 2 %, 50 ppm, 30 ohm, SURFACE MOUNT, 0603, CHIP

M55342H12B30G0MT1 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1866523641
package instructionSMT, 0603
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL7.85
Other featuresNON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length1.6256 mm
Package formSMT
Package width0.8128 mm
method of packingTR
Rated power dissipation(P)0.1 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance30 Ω
Resistor typeFIXED RESISTOR
size code0603
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTIN LEAD OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance2%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
iic_eeprom simulation problem
According to Mr. Xia Wenyu's method, when reading data, when starting to write 1010 0011 for the second time, the last 1 cannot be written in. It is found that the enable end is raised one cycle in ad...
xjlnuc FPGA/CPLD
After the PWM frequency of STM32 reaches 500KHZ, can it be increased or decreased by 1KHZ?
After the PWM frequency of STM32 reaches 500KHZ, can it be increased or decreased by 1KHZ?1. When I set the frequency to 500KHZ, I can capture the waveform of 500KHZ with an oscilloscope. When I want ...
西点钟灵毓秀 stm32/stm8
ESP32-S2 Development Pitfalls—by RCSN
ESP32-S2 Development PitfallsAuthor: RCSNTable of contents ESP32-S2 development pit (1) - open filling ESP32-S2 Development Pitfalls (2) -- Cmake Construction Engineering System ESP32-S2 development p...
okhxyyo DIY/Open Source Hardware
Is there any good way to reduce the noise received by the RF receiving circuit?
I am working on a 51 project these days. I need to use the RC-R01A RF receiving module. The module is connected to the RXD serial port receiving end of the 51 microcontroller. However, during the expe...
HALO--117 RF/Wirelessly
Motor drive MOS reasons
What is the reason for sparks under the motor drive MOS tube?...
田家一 Electronics Design Contest
Looking for a program about msp430 and sensors that follow the modbus protocol
Newbie posting, I don't know how to write a program yet...
飘过无名 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2335  1590  1825  551  2373  48  33  37  12  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号