EEWORLDEEWORLDEEWORLD

Part Number

Search

MEB-824K0100DT1109

Description
CAPACITOR, METALLIZED FILM, POLYESTER, 100V, 0.82uF, THROUGH HOLE MOUNT, RADIAL LEADED
CategoryPassive components    capacitor   
File Size444KB,2 Pages
ManufacturerHua Jung Co., Ltd.
Download Datasheet Parametric View All

MEB-824K0100DT1109 Overview

CAPACITOR, METALLIZED FILM, POLYESTER, 100V, 0.82uF, THROUGH HOLE MOUNT, RADIAL LEADED

MEB-824K0100DT1109 Parametric

Parameter NameAttribute value
Objectid1144741894
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresFLAME PROOF; NON-INDUCTIVE
capacitance0.82 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYESTER
JESD-609 codee3
Manufacturer's serial numberMEB
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package shapeRECTANGULAR PACKAGE
method of packingTAPE
positive tolerance10%
Rated (DC) voltage (URdc)100 V
surface mountNO
Terminal surfaceTIN
Terminal shapeWIRE
Can an expert please help me take a look? It would be best if you could help me revise it. I don't understand. It's my graduation project. It's urgent!
#include#include#include #include #include #include#define A8251 0x308 #define Com8255 0x303 #define PA8255 0x300 #define PB8255 0x301 #define PC8255 0x302 #define data51 0x308 /* 8251 data port addre...
chg4476 Embedded System
wince4.2 Press the power button to start the program (not cold start or hot start)
I made an application on Symbol mc1000, and the machine is installed with Wince 4.2. My program will be cleared during cold start and will enter my program during hot start. However, I want to enter m...
litiantao Embedded System
When using cycloneV's development board to write an interrupt response program, why does the F2S_IRQ1 interrupt number not respond?
Previously, I successfully wrote an interrupt program that uses the HPS button to control the HPS LED light. The interrupt method used was GPIO1. Now I want to send an interrupt signal through the FPG...
包玉刚 FPGA/CPLD
Help, automotive electronics,
How to send the gear position signal of the car to the processor? There are two signals, forward gear and reverse gear. What specific circuit is needed? Please help! ! !...
as心的距离 Automotive Electronics
Is there an Atmel agent? Contact me
ATSAMD21G17A-MUT...
MTDZCJW Microchip MCU
How to solve the problem of field effect tube heating when used as a switch
[i=s]This post was last edited by Xiaodong Engineer on 2021-5-6 10:21[/i]When the NCE0102Z field effect tube is used as a switch, D (drain) is added with a 12V voltage, G (gate) is connected to a PWM ...
小东工程师 Switching Power Supply Study Group

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1582  243  552  2714  2835  32  5  12  55  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号