EEWORLDEEWORLDEEWORLD

Part Number

Search

3GW14D-150T-250.00

Description
LVCMOS Output Clock Oscillator, 250MHz Nom, ROHS AND REACH COMPLIANT PACKAGE-14/4
CategoryPassive components    oscillator   
File Size122KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

3GW14D-150T-250.00 Overview

LVCMOS Output Clock Oscillator, 250MHz Nom, ROHS AND REACH COMPLIANT PACKAGE-14/4

3GW14D-150T-250.00 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1078111865
package instructionROHS AND REACH COMPLIANT PACKAGE-14/4
Reach Compliance Codecompliant
Maximum control voltage2.31 V
Minimum control voltage0.99 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate150 ppm
frequency stability25%
linearity10%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency250 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVCMOS
Output load15 pF
physical size20.2mm x 12.8mm x 5.08mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
EURO
QUARTZ
14 pin Dual-in-Line VCXO
Frequency range 200.1MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
DESCRIPTION
OUTLINE & DIMENSIONS
GW42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. GW42 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GW14 VCXO
200.1MHz ~ 800.0MHz
200.1MHz to 800.0MHz
3.3 VDC ±5%
LVCMOS
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
PHASE NOISE
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
)
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
3GW14B-80N-250.00
Supply Voltage
3 = +3.3V
Series Designator
GW14
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
STM32L051's ADC conversion is inaccurate after wakeup
[font=宋体][size=5]After waking up from STM32L051 stop mode, the voltage converted by ADC is inaccurate. It needs to be initialized before each conversion. Has anyone encountered a similar situation? Pl...
943614033 stm32/stm8
STM32F429Discovery oscilloscope test heart rate
I was testing the pulse sensor at night and wondered if the STM32F429Discovery oscilloscope could be used to measure the waveform, so I tried it. Set the CH1 input, T=500ms, and adjust the offsetThe o...
dcexpert stm32/stm8
Question about bootloader interrupt vector
After reading the bootloader, I have some doubts: 1. When an exception occurs, the interrupt vector table is forced to jump by hardware according to the exception, and then the service program address...
taotaotalk Embedded System
Distribution analysis and maintenance of common faults in plc process control systems
In order to extend the life of the PLC control system, it is necessary to have a clear estimate of the equipment consumption and the failure points of the components and equipment in the system design...
frozenviolet Industrial Control Electronics
Discussing WINCE TCP/IP programming?
The PC version of TCP/IP has controls, but the WINCE version does not. It only has a SOCKET. Now some industrial control systems use TCP/IP, big data, real-time, and wireless. The serial port is also ...
tysym Embedded System
After installing the USB filter driver, how to solve the blue screen after restart?
Following the example in Chapter 22 of Zhang Fan's "Detailed Explanation of Windows Driver Development Technology", I made a USB filter driver and disabled the USB drive. After installing it and resta...
kunlun Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 822  42  2454  2878  792  17  1  50  58  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号