EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

YDTS26T25-04SA0000

Description
MIL Series Connector
CategoryThe connector    The connector   
File Size67KB,2 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

YDTS26T25-04SA0000 Overview

MIL Series Connector

YDTS26T25-04SA0000 Parametric

Parameter NameAttribute value
Objectid7389938397
Reach Compliance Codeunknown
ECCN codeEAR99
Body/casing typePLUG
Connector typeMIL SERIES CONNECTOR
Contact arrangementS48P8
Contact to complete cooperationNOT SPECIFIED
Contact point genderFEMALE
Contact materialNOT SPECIFIED
Contact styleRND PIN-SKT
DIN complianceNO
Electromagnetic interference shieldingYES
empty shellYES
Filter functionNO
IEC complianceNO
MIL complianceNO
Power Connector Ratings13A
Mixed contactsYES
Installation typePANEL
Number of connectorsONE
Number of ports1
Maximum operating temperature200 °C
Minimum operating temperature-65 °C
OptionsGENERAL PURPOSE
Panel mountingNO
polarizationA
polarization keyPOLARIZED
Rated current (signal)13 A
Shell surfaceNICKEL PTFE
Shell materialALUMINUM ALLOY
Housing size25
Total number of contacts56
Maximum wire diameter16 AWG
Minimum wire diameter20 AWG
Why does the transistor loss in the OCL circuit increase with increasing frequency?
The circuit is shown in the figure. The front-stage transistors of the OCL circuit are: NPN-PBSS8110Y, PNP-PBSS9110Y. The models of the rear-stage transistors are: NPN-NSS1C301ET4G, PNP-NSS1C300ET4G. ...
咖啡不加冰 Analog electronics
[Ask] SuperIO watchdog issue
I am working on the software side of a hardware project and now I have a problem that I would like to ask for a solution. A motherboard is connected to an MCU, which controls the voltage regulation or...
fengboning Embedded System
DCDC ripple experiment
Notes on using an oscilloscope to test rippleMeasure using the AC coupling mode of the oscilloscopeBecause the oscilloscope head cover is easy to introduce noise, the probe head cover must be removed ...
灞波儿奔 Analogue and Mixed Signal
Solution to the problem of automatic restart of the target board when debugging the UP-TECH2410 board with JLINK
The problem is this: About a month ago, I built a S3C2410 project on IAR6.1. I have two boards, one FS2410 board from Youlong and two UP-TECH2410 boards from Broadcom. There are two debuggers for that...
zsjalive Integrated technical exchanges
Help! FPGA 1.2V short circuit to ground
[color=#666666][font=arial, 宋体]I soldered a board myself. It was running fine, but suddenly the program configuration failed. I measured and found that the 1.2V would short-circuit as soon as it was p...
鹰翔寰宇不会变 FPGA/CPLD
Writing a program
I want to write a program with MSP430. How can I program the output to display the amplitude value of a known frequency?...
wxw6987 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2728  2550  1078  2293  1380  55  52  22  47  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号