EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B3Y52ST0

Description
Fixed Resistor, Thin Film, 0.25W, 3520ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B3Y52ST0 Overview

Fixed Resistor, Thin Film, 0.25W, 3520ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP

D55342E07B3Y52ST0 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145080864264
package instructionCHIP
Reach Compliance Codenot_compliant
Country Of OriginUSA
YTEOL7.45
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance3520 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
I am a newbie. I installed CCS3.3 but it can't be opened. It shows an error. I have screenshots and would like your advice.
I am a newbie. I installed CCS3.3 but it can't be opened. It shows an error. I have screenshots and would like your advice....
lb2898 DSP and ARM Processors
Motorola Electronic Design Competition Outstanding Works (Part 9)
[i=s]This post was last edited by paulhyde on 2014-9-15 08:54[/i]...
clark Electronics Design Contest
Which expert please give me some advice: Bias of signal waveform
Could any expert please give me some advice on the bias of the signal waveform? I want to offset a triangle wave with a base point of 2.5V, a maximum point of 3.6V, and a minimum point of 1.3V to the ...
kibby0 Analog electronics
Problems on connecting the neutral points of two DC circuits with different voltages
[i=s]This post was last edited by sunboy25 on 2017-6-6 10:08[/i] I would like to ask why the circuit can still work normally after the two neutral points A and B in the circuit diagram below are conne...
sunboy25 Power technology
This week's highlights
[url=https://e2echina.ti.com/question_answer/dsp_arm/sitara_arm/f/25/t/134026][font=微软雅黑][size=4]EtherCAT implemented based on CPSW of AM335x[/size][/font][/url][font=微软雅黑][size=4][color=#000000] [/co...
橙色凯 DSP and ARM Processors
Talk about my IRIG-B custom component design and debugging summary based on SOPC
Keywords: SOPC, custom component, IRIG-B, debugging [b]I. Case description [/b] Recently, I plan to use SOPC to build a system to complete the upgrade of the project platform. Since the platform based...
wdgui522 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1338  904  844  89  116  27  19  17  2  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号