EEWORLDEEWORLDEEWORLD

Part Number

Search

MR061A122FTTTR1

Description
Ceramic Capacitor, Ceramic, 100V, 1% +Tol, 1% -Tol, C0G, -/+30ppm/Cel TC, 0.0012uF, 2909,
CategoryPassive components    capacitor   
File Size181KB,8 Pages
ManufacturerAVX
Download Datasheet Parametric View All

MR061A122FTTTR1 Overview

Ceramic Capacitor, Ceramic, 100V, 1% +Tol, 1% -Tol, C0G, -/+30ppm/Cel TC, 0.0012uF, 2909,

MR061A122FTTTR1 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid756091726
package instruction, 2909
Reach Compliance Codenot_compliant
ECCN codeEAR99
YTEOL5.7
capacitance0.0012 µF
Capacitor typeCERAMIC CAPACITOR
dielectric materialsCERAMIC
high7.36 mm
JESD-609 codee0
length7.36 mm
negative tolerance1%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formRadial
method of packingTR
positive tolerance1%
Rated (DC) voltage (URdc)100 V
seriesMR
size code2909
Temperature characteristic codeC0G
Temperature Coefficient30ppm/Cel ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal pitch5.08 mm
width2.28 mm
Radial Leads/Ceralam
®
GENERAL INFORMATION
Dimensions: Millimeters (Inches)
AVX MR Series
Molded Radial Leaded MLC
Temperature Coefficients:
C0G (NP0), X7R, Z5U
50, 100, 200 Volts
Case Material:
Molded Epoxy
Lead Material:
Solderable
1.14 (.045)
Max.
31.7 (1.25)
Min.
W
L
T
L.D.
W
31.7 (1.25)
Min.
L
T
L.S.
Style MR05
L.D.
L.S.
Styles MR04, MR06,
MR07, MR08
HOW TO ORDER
MR05
AVX Style
MR04
MR05
MR06
MR07
MR08
1
Voltage
5 = 50V
1 = 100V
2 = 200V
A
Dielectric
A = C0G (NP0)
C = X7R
E = Z5U
561
Capacitance
First two digits are the significant
figures of capacitance. Third digit
indicates the additional number
of zeros. For example, order
100,000 pF as 104. (For values
below 10pF use “R” in place of
decimal point, e.g., 1R4 = 1.4pF.)
J
Capacitance
Tolerance
C0G (NP0):
D = ±.5pF
(>10pF only)
F = ±1%
(>50pF only)
G = ±2%
(>25pF only)
J = ±5%
K = ±10%
X7R:
J = ±5%
K = ±10%
M = ±20%
Z5U:
M = ±20%
Z = +80%
-20%
A
Failure Rate
A = Not Applicable
T = CECC
A
Leads
A = Standard
Solderable (SnPb)
T
1
= Trimmed Leads
.230" ± .030"
1
Trimmed lead length for the MR05 style will be measured from the bend in the lead (seating plane).
MARKING
Marking is as size permits.
(For code identification, see HOW TO ORDER section.)
— AVX
— Capacitance Tolerance
— Voltage Rating
— Temperature Coefficient
— Date Code
— Lot Code
PACKAGING REQUIREMENTS
Bulk Packaging:
1000 pcs. per sealed package except
MR07/MR08 (300 pcs.).
Tape and Reel:
Available on MR04, MR05, and MR06
only (2500 pcs./reel).
Ammo Packaging:
Available on special request.
29
The Confessing Child
As a beginner in microcontrollers, I was quite passionate about it at first, but when I learned about interrupts, I was confused by the registers and commands. I don’t know why, but I was annoyed and ...
太阳上的骑士 51mcu
Atmel SAM D21 development board trial experience + OLED display RTC clock
[i=s] This post was last edited by wgsxsm on 2014-10-27 11:36 [/i] Time is limited. I did not start from the bottom. I could only look for a transplantation solution in the Atmel Studio routine. I had...
wgsxsm MCU
Ask TI engineers for help???
Hope to have the opportunity to communicate with TI engineers! ! ! I have recently been studying TMS320DM365 and TMS320DM368 video stream processing chips. I encountered problems when building the dev...
37°男人 DSP and ARM Processors
Design a tester for measuring resistance and inductance using a DC digital multimeter (5-digit, maximum input voltage 10V).
(1) Resistance measurement range: 10~1KΩ. (2) Inductance measurement range: 100H~10mH. (3) The measured resistance and inductance values can be directly displayed on the DC digital voltmeter. (4) It h...
15769550549 Analogue and Mixed Signal
On the last day of 2019, make a New Year’s wish for 2020!
Today is the last day of 2019. Have all your wishes come true and all your plans completed this year? It doesn’t matter if it’s not achieved or completed, at least we have tried! At the end of the yea...
eric_wang Talking
Can the SWIM pin of the STM8L101xx microcontroller be used as a normal IO port? ? ? ?
I want to use a STM8L101xx series microcontroller. To save space, I want to choose a 20-pin model. However, I need 17 IO ports in total. Can I use the SWIM pin as a normal IO port? I want to use this ...
wenqing870714 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1513  1057  972  18  1719  31  22  20  1  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号