EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV42C-30N-200.000

Description
Oscillator, 50.01MHz Min, 200MHz Max, 200MHz Nom,
CategoryPassive components    oscillator   
File Size128KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GV42C-30N-200.000 Overview

Oscillator, 50.01MHz Min, 200MHz Max, 200MHz Nom,

3GV42C-30N-200.000 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid109584754
Reach Compliance Codecompliant
Installation featuresSURFACE MOUNT
Number of terminals4
Maximum operating frequency200 MHz
Minimum operating frequency50.01 MHz
Nominal operating frequency200 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Package body materialCERAMIC
Encapsulate equivalent codeDILCC4,.38,200
power supply3.3 V
Certification statusNot Qualified
Maximum slew rate25 mA
Nominal supply voltage3.3 V
surface mountYES
EURO
QUARTZ
LVCMOS SMD 11.4 x 9.6 x 2.5mm, 4 pad
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
OUTLINE & DIMENSIONS
DESCRIPTION
GV42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. The VCXO incorporates a high Q
fundamental mode crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GV42 VCXO
50.01MHz ~ 200.0MHz
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
PHASE NOISE
)
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
3GV42B-80N-155.25
Supply Voltage
3 = +3.3V
Series Designator
GV426
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Please help me, I believe this problem is not difficult for you, I sincerely thank you all!!
:kiss: I would like to ask for your help. I believe this problem is not difficult for you. I would like to thank you all for designing an example of 8051 microcontroller. All operations are completed ...
我想学 51mcu
Looking for STM32 SPI2 and SPI3 master-slave communication settings
I searched for several solutions online and tried them all, but they still don't work. Is it okay to set both SPI pins to output after push, and only set the master and slave in the SPI settings to be...
kaka009 stm32/stm8
C language discussion thread
The development of DSP2812 is inevitably related to C language. For the dsp2812 board, C is the main language, and some structures of C++ are also referred to, and there are grammatical features that ...
gaoxiao Microcontroller MCU
Fujitsu FRAM Experience Submission
Fujitsu FRAM and Arduino Uno Fujitsu FRAM is MB85RC128, Arduino Uno is selected as I2C master. MB85RC128 pin 8 connects to 3.3v pin 4 connects to ground pin 6 connects to I2C SCL pin 5 connects to I2C...
huangwarrenus Integrated technical exchanges
Little Luohan has a meeting
I picked it last night, it looks delicious. Let's study it together and see if eating it can make you immortal:P...
johnrey Talking
Why does lut1lut's "STR71x UART IAP" need to be copied manually again?
In lut1lut's "How to use STR71x UART for IAP Supplementary Instructions Version 1.0", if the user program wants to use interrupts, the exception vector table, startup code and interrupt handling funct...
ltfss stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1786  767  2752  2166  108  36  16  56  44  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号