www.fairchildsemi.com
RV4145A
Low Power Ground Fault Interrupter
Features
•
•
•
•
No potentiomenter required
Direct interface to SCR
Supply voltage derived from AC line – 26V shunt
Adjustable sensitivity
•
•
•
•
Grounded neutral fault detection
Meets U.L. 943 standards
450µA quiescent current
Ideal for 120V or 220V systems
Description
The RV4145A is a low power controller for AC outlet
ground fault interrupters. These devices detect hazardous
grounding conditions, such as equipment (connected to
opposite phases of the AC line) in contact with a pool of
water and open circuits the line before a harmful or lethal
shock occurs.
Contained internally are a 26V zener shunt regulator, an op
amp, and an SCR driver. WIth the addition of two sense
transformers, a bridge rectifier, an SCR, a relay, and a few
additional components, the RV4145A will detect and protect
against both hot wire to ground and neutral wire to ground
faults. The simple layout and conventional design ensure
ease of application and long-term reliability.
Block Diagram
RV4145A
V
FB
R1
10K
R2
10K
V
REF
(+13V)
+V
S
(+26V)
+Input
Op Amp Output
6.5V
6.5V
6.5V
6.5V
Ground
R3
4.7K
65-4145A-01
SCR Trigger
REV. 1.0.3 3/6/02
PRODUCT SPECIFICATION
RV4145A
Principles of Operation
The 26V shunt regulator voltage generated by the string of
zener diodes is divided into three reference voltages: 3/4 V
S
,
1/2 V
S
, and 1/4 V
S
. V
REF
is at 1/2VS and is used as a refer-
ence to create an artifical ground of +13V at the op amp non-
inverting input.
Figure 1 shows a three-wire 120V AC outlet GFI application
using an RV4145A. Fault signals from the sense transformer
are AC coupled into the input and are amplified according to
the following equation:
V
7
= R
SENSE
×
I
SENSE
/N
Where V
7
is the RMS voltage at pin 7 relative to pin 3,
R
SENSE
is the value of the feedback resistor connected from
pin 7 to pin 1, I
SENSE
is the fault current in amps RMS and
N is the turns ratio of the transformer. When V
7
exceeds plus
or minus 7.2V relative to pin 3 the SCR Trigger output will
go high and fire the external SCR.
The formula for V
7
is approximate because it does not
include the sense transformer characteristics.
Grounded neutral fault detection is accomplished when a
short or fault closes a magnetic path between the sense trans-
former and the grounded neutral transformer. The resultant
AC coupling closes a positive feedback path around the op
amp, and therefore the op amp oscillates. When the peaks of
the oscillation voltage exceed the SCR trigger comparator
thresholds, the SCR output will go high.
The roll-off frequency is greater than the grounded neutral
fault oscillation frequency, in order to preserve loop gain for
oscillation (which is determined by the inductance of the
200:1 transformer and C4).
The senstivity to grounded neutral faults is adjusted by
changing the frequency of oscillation. Increasing the fre-
quency reduces the sensitivity by reducing the loop gain of
the positive feedback circuit. As frequency increases, the
signal becomes attenuated and the loop gain decreases. With
the values shown the circuit will detect a grounded neutral
fault having resistance of 2
Ω
or less.
The input to the op amp are protected from overvoltage by
back-toback diodes.
SCR Driver
The SCR used must have a high dV/dt rating to ensure that
line noise (generated by noisy appliances such as a drill
motor) does not falsely trigger the SCR. Also, the SCR must
have a gate drive requirement of less than 200µA. C
F
is a
noise filter capacitor that prevents narrow pulses from firing
the SCR.
The relay solenoid used should have a 3ms or less response
time in order to meet the UL 943 timing requirement.
Sense Transformers and Cores
The sense and grounded neutral transformer cores are usu-
ally fabricated using high permeability laminated steel rings.
Their single turn primary is created by passing the line and
neutral wires through the center of its core. The secondary is
usually from 200 to 1500 turns.
Magnetic Metals Corporation, Camden, NJ 08101,
(609) 964-7842, and Magnetics, 900 E. Butler Road,
P.O. Box 391, Butler, PA 16003, (412) 282-8282 are full line
suppliers of ring cores and transformers designed specifi-
cally for GFI applications.
Shunt Regulator
R
LINE
limits the current into the shunt regulator; 220V
applications will require substituting a 47k
Ω
2W resistor. In
addition to supplying power to the IC, the shunt regulator
creates internal reference voltages (see above).
Operational Amplifier
R
SENSE
is a feedback resistor that sets gain and therefore
sensitivity to normal faults. To adjust R
SENSE
, follow this
procedure: apply the desired fault current (a difference in
current of 5mA is the UL 943 standard). Adjust R
SENSE
upward until the SCR activates. A fixed resistor can be used
for R
SENSE
, since the resultant ±15% variation in sensitivity
will meet UL’s 943 4-6mA specification window.
Two-Wire Application Circuit
Figure 2 shows the diagram of a 2-wire 120V AC outlet GFI
circuit using an RV4145A. This circuit is not designed to
detect grounded neutral faults. Thus, the grounded neutral
transformer and capacitors C3 and C4 of Figure 1 are not
used.
4
REV. 1.0.3 3/6/02
京公网安备 11010802033920号
EEWORLD
