EEWORLDEEWORLDEEWORLD

Part Number

Search

701022.940.02

Description
Fixed Resistor, Wire Wound, 0.33W, 2.94ohm, 300V, 0.02% +/-Tol, -2,2ppm/Cel,
CategoryPassive components    The resistor   
File Size78KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

701022.940.02 Overview

Fixed Resistor, Wire Wound, 0.33W, 2.94ohm, 300V, 0.02% +/-Tol, -2,2ppm/Cel,

701022.940.02 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid713930785
Reach Compliance Codecompliant
ECCN codeEAR99
structureTubular
Lead diameter0.8 mm
Lead length38.1 mm
Number of terminals2
Maximum operating temperature145 °C
Minimum operating temperature-65 °C
Package diameter6.3 mm
Package length12.7 mm
Package shapeTUBULAR PACKAGE
Package formAxial
Rated power dissipation(P)0.33 W
GuidelineMIL-R-93
resistance2.94 Ω
Resistor typeFIXED RESISTOR
series7000(AXIAL)
technologyWIRE WOUND
Temperature Coefficient2 ppm/°C
Tolerance0.02%
Operating Voltage300 V
Axial Lead Precision
Wirewound Resistors
RB / RBR, VA / HR, SP / 7000 Series
0.1 to 1.0 watts
Tolerance to ±.01%
0.1 ohm to 12 meg ohms
Approved to M, P, & R levels
TCR’s from ±2 ppm/°C to +6000 ppm/°C
Meets or exceeds all applicable MIL-R-93 & MIL-R-39005 ratings
The RB/RBR ultra precision resistors are designed and produced for critical parameter applications. They are available
for established reliability military and/or commercial applications requiring state of the art precision and stability.
Construction features may vary slightly between commercial and military styles, but both are produced under the same
rigid quality control system required by the tightest military specifications. Both are produced in the same production
line using the same highly trained operators required to produce the established reliability product.
All terminations are welded to reduce contact noise and thermal EMF. Extensive accelerated aging programs both
before and after calibration assure precise initial accuracy and high resistance stability.
Encapsulation is accomplished by a unique dry air chamber epoxy shell technique for established reliability parts. A
resilient inner coating is used to minimize internal stresses on all parts.
All resistors (military and commercial) are carefully monitored during assembly, winding, coating, and stabilization
procedures to assure high quality standards. Premium grade selected wire is control- stress wound on special designed
bobbins. Established reliability military parts are then burned in for 100 hours at 125°C ambient as part MIL-R-93, or
equivalent, of group A acceptance testing. Documentation and special tests are available upon customer request to
meet your unique requirements.
TCR and Temperature Data
Style
Resistance Range (Ω)
0.1 - 0.9
All
Styles
1.0 - 9.9
10 - 99.9
100 - 12M
Absolute TCR (ppm/°C)
±90
±30
±15
±10
-65 to +145
Operating Temperature Range (°C)
Special Screening / Acceptance Test:
Special tests can be performed on a 100% or sample basis, to meet individual customer requirements. Some of the
available non-destructive tests include:
• Short Time Overload
• Thermal Shock
• Mechanical Shock
• Vibration
• Temperature Coefficient of Resistance
• Radiographic Inspection
Each of these tests is designed to detect a spectrum of potential resistor defects. Consult the factory for recommendations
and a quotation on special screening or acceptance tests to meet your needs.
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
RB/RBR, VA/HR, SP/ 7000 Series Issue January 2010 Sheet 1 of 4
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
SDRAM read and write test in EBOOT
Heroes: My system is based on pxa255+wce4.2, with two banks of sdram, each bank is connected to 64M, and consists of two 32M chips. In eboot, to test sdram, I read and write the addresses of the two b...
shangyl Embedded System
Simple circuit and powerful performance ECG acquisition circuit
[i=s]This post was last edited by Mandy on 2015-2-11 09:46[/i] This human ECG signal acquisition circuit was DIYed by me when I first started to use analog circuits. I used TI's solution and samples f...
Mandy Analogue and Mixed Signal
TRACE32 Model LA-7708 for sale at low price
Low price transfer TRACE32 model LA-7708 Price 20,000, accept small knife, if you need it, contact: 13713676870...
wu1239 Embedded System
Selling a Digilent Basys3 FPGA development board
[size=14px]I am studying in the United States, and I bought a Basys3 FPGA development board for study. But since I am not a major FPGA developer, the board is idle and I plan to sell it. The board is ...
masonmvp Buy&Sell
In AD, the ID changes always occur when the schematic is imported into the PCB
I drew the PCB board with AD and established a project. There are schematics and corresponding PCB boards in the project. The schematics can be fully used after being imported into the PCB. Everything...
工控小学徒 PCB Design
hc32f460
Can any of you help me take a look? My boss said that I didn't enable the system clock. Can anyone tell me how to enable the system clock?...
逃之之夭夭 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2695  439  901  2101  181  55  9  19  43  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号