550103M200DE0FS datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> 550103M200DE0FS

550103M200DE0FS: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 10000uF,; CategoryPassive components capacitor; File Size407KB，8 Pages; ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]; Environmental Compliance

Download Datasheet Parametric View All

550103M200DE0FS Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 10000uF,

550103M200DE0FS Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	844322886
package instruction	,
Reach Compliance Code	unknown
ECCN code	EAR99
YTEOL	6.98
capacitance	10000 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
diameter	76.2 mm
dielectric materials	ALUMINUM
ESR	9.2 mΩ
length	130.18 mm
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
Package form	Screw Ends
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	200 V
ripple current	31300 mA
series	550
Terminal pitch	31.75 mm

Preview

Download Datasheet

View All

Type 550

105 °C High Ripple, Long-life, Inverter Grade, Aluminum

High Ripple, Long Life, Computer Grade

High Value, High Ripple Current

Type 550 is the original Inverter Grade capacitor for continuous

operation at up to 105 °C and it now is available in low voltages too.

For best value its load life test is 2000 hours instead of the 5000

hours of the Type 550C. While less than half the life capability of

the Type 550C, it is lower cost and easily lasts more than 10 years

in typical industrial applications.

Highlights

•

2,000 hour load life

Ripple current to >50 amps

ESRs to 2.5 mΩ

–40 °C to +105 °C

6.3 to 450 Vdc

90 µF to 1.5 F

Vdc ≤ 150 V: –10 +75%, Vdc > 150 V: –10 +50%

≤3√CV µA (4 mA max.)

Ambient Temperature

45 °C

1.73

55 °C

1.58

65 °C

1.41

75 °C

1.22

85 °C

1.00

95 ºC

0.71

105 ºC

0.57

Specifications

Operating Temperature:

Rated Voltage:

Capacitance:

Capacitance Tolerance:

DCLeakage Current:

Ripple Current Multipliers:

Frequency

10 kHz

50 Hz 60 Hz 120 Hz 360 Hz 1 kHz 5 kHz @ up

1⅜ and 2 inch diameter

≤ 50 V

51–299 V

≥300 V

2½ and 3 inch diameter

≤ 50 V

51–299 V

≥300 V

Load Life:

Shelf Life:

Vibration:

Complies with the EU Directive

2002/95/EC requirement restricting

the use of Lead (Pb), Mercury (Hg),

Cadmium (Cd), Hexavalent chromium

(Cr(VI)), PolyBrominated Biphenyls

(PBB) and PolyBrominated Diphenyl

Ethers (PBDE).

0.77

0.75

0.72

0.81

0.72

0.85

0.83

0.80

0.90

0.80

1.00

1.05

1.15

1.30

1.02

1.07

1.25

1.08

1.20

1.40

1.02

1.07

1.35

1.08

1.20

1.40

1.02

1.07

1.35

1.08

1.20

1.40

1.02

1.07

1.35

2,000 h at full load @ 105 °C

500 h @ 105 °C, Capacitance, ESR and DCL, initial

requirements.

0 to 55 Hz, 0.06” and 10 g max, 1.5 h each of 2 axis

CDM Cornell Dubilier

•

140 Technology Place

•

Liberty, SC 29657

•

Phone: (864)843-2277

•

Fax: (864)843-3800

•

www.cde.com

Recommended Resources

Three-phase alternating current detection circuit

IC directly drives LED display circuit

Switching power supply circuit using MC44603P

STK4352 power amplifier circuit diagram

Amplitude modulation detector circuit using ULN2209 and MC1496K

Transformers, RC and direct-coupled amplifiers

Exploration on Optimization of Jianou Telephone Network: Abstract: Based on the current situation of Jianou telephone network, this paper analyzes the application of transmission network, switching network and access network technology according to the tren...; gheui RF/Wirelessly

The problem of debugging c51 in keil is probably related to compilation. Please help: Problems with variable values [code]void main() { unsigned int a1; unsigned int b1; unsigned char h; unsigned char l; a1=0xab12; l=a1; b1=(a1&0xff00)/256; h=b1; }[/code] When debugging with KEIL, I fo...; stone3w Embedded System

Dear experts, please help me look at a program about F5529: I want to use F5529 to output a sine wave. Below is my program, but there is no waveform. I beg you experts to help me find out why #include #include "HAL_Dogs102x6.h" #define SCLK_HIGH P4OUT |= BIT5 ...; 李雪莹 Microcontroller MCU

Please advise: PCI9054 reset: Reset: In order to download the program to DSP through HPI, it is necessary to independently control the reset of DSP. 1〉Set the value of CPLD register xrun_flag_en to 0; (the address of Local termina...; zserfv8210 Embedded System

USB to serial port driver under CE: I have been quite free recently. I made a driver for USB to serial port under CE. It works very well. You can download it from http://download.eeworld.net/source/1666208. It contains the driver and th...; piaoxuwjx Embedded System

Precautions for installing high-power LED floodlights and LED underwater lights: New light source: adopts high-power white light LED 30W light source, with high light efficiency, long service life and long-term maintenance-free 　　Energy-saving performance: precise constant current...; 探路者 LED Zone

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components