BN2500EIHOOFC-PF datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> BN2500EIHOOFC-PF

BN2500EIHOOFC-PF: DescriptionParallel - Fundamental Quartz Crystal, 25MHz Nom,; CategoryPassive components Crystal/resonator; File Size543KB，3 Pages; ManufacturerAdvanced Crystal Technology; Websitehttp://www.actcrystals.com; Environmental Compliance

Download Datasheet Parametric View All

BN2500EIHOOFC-PF Overview

Parallel - Fundamental Quartz Crystal, 25MHz Nom,

BN2500EIHOOFC-PF Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145181370696
Reach Compliance Code	unknown
Ageing	3 PPM/FIRST YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	10 µW
frequency stability	0.002%
frequency tolerance	10 ppm
load capacitance	12 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	25 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-20 °C
physical size	3.2mm x 2.5mm x 0.7mm
Series resistance	30 Ω
surface mount	YES

Preview

Download Datasheet

View All

ACT320SMX-4 Seam Sealed 4 pad Crystal Resonator

●

High quality low aging 3.2x2.5mm crystal.

±3ppm aging first year, & tighter aging options

±10ppm stabilty over -20~+70°C

Pads 2 &4 grounded to the lid

Characteristics

Frequency Range (MHz)

Operating temperature Top (°C)

Tolerance @ 25°C (ppm)

Stabilty over temperature (ppm)

Effective Series Resistance (Ω)

Shunt capacitance (C0) (pF)

Aging @25°C (ppm)

Load capacitance (pF)

Drive level (µW)

Drive level dependancy (DLD2) (Ω)*

Drive level dependancy (FLD) (ppm)*

Insulation resistance @100V

Rating

Storage temperature (°C)

-40 ~ 85

MSL

1 (unlimited)

ESD

Not applicable

Notes:

1. * 6 steps minimum

2. ±11ppm tolerance including 1st year aging for some specifications, enquire.

12 ~ 54

Table 2

±10, ±15, ±20, ±30, ±50

Table 1 and 2

Table 1

5 (max)

±3 std,

option note 2

8 ~ 50 & series

10µW typ 100µW max

<10Ω

<10ppm

500MΩ min

Please note that all parameters can not necessarily be specified in the same device.

To specify: Please refer to part numbering system appended to the end of this data

ISO9001 Registered

For quotations or further information please contact us at:

3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY

Issue No.

18 C1F

Date:

11/04/2016

320SMX-4

Tel

Fax:

email:

0044(0)118 979 1238

0044(0)118 979 1283

info@act crystals.com

Recommended Resources

Simple and practical mini programmer schematic diagram

Programmable lantern controller circuit

Output adjustable switching regulator circuit diagram

OPT209 gain adjustment circuit

Novel and practical voltage doubler ballast circuit diagram

Voltage-current conversion circuit

msp430 1602 display: [color=Red][color=Red]#include "msp430g2553.h"void delay(int i) {unsigned int a,b; for(a=i;a>0;a--)for(b=1111;b>0;b--);} void busy() {unsigned char BF;P2OUT |=BIT1;P2OUT &=~BIT2;P2OUT &=~BIT0;BF=(P1IN...; ww_1 Microcontroller MCU

STM32 trigger interrupt debounce problem: I just started to learn 32 and I am writing a program for drip control. In the last process, I found that the interrupt will be triggered many times in a short period of time. I want to add a debounce...; 青竹之初 stm32/stm8

Driving external RF front end via BlueNRG-LP: The BlueNRG-LP is an ultra-low-power Bluetooth low energy SoC device that can reach +8 dBm output power at the antenna connector. However, the maximum output power allowed by the Bluetooth standard is...; littleshrimp ST - Low Power RF

National Undergraduate Electronic Design Competition…First Prize Works (3): [i=s]This post was last edited by paulhyde on 2014-9-15 09:06[/i] [size=5]RF signal source, semiconductor thermostat design, multi-channel temperature inspection instrument, human heart rate detection...; lk972105 Electronics Design Contest

About ADC automatic calibration: When we use ADC,we usually calibrate it when we first turn it on.I would like to askif the MCU temperature changes during operation and the internal temperature of the MCU rises or falls by a few degr...; wuh2003 stm32/stm8

stm8 timer 2 channel cannot adjust pwm waveform: void TIM2_init() { TIM2->PSCR = 0; // Initialize the clock divider to 1, that is, the clock frequency of the counter is Fmaster=4MHZ TIM2->CCMR2 = TIM2->CCMR2 | 0x70; // Output mode PWM2 // Channel 2 ...; l217914 stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components