3) Electrodes not corroded by soldering Thick film makes
the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1976 (first in the wold),
this component has established a solid reputation as
a general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°
C.
100
80
60
40
20
0
Specifications
0.25W (1 / 4W)
at 70
°
C
POWER LOAD (%)
−55
0
70
100
155
AMBIENT TEMPERATURE (
°
C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E= P
×
R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55
°
C
to + 155
°
C
Max. intermittent overload voltage
400V
Max. operating voltage
200V
Max. overload voltage
400V
MCR18
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
F ( ± 1%)
Table 1
Resistance tolerance
Resistance range
(Ω)
10
≤
R
≤
2.2M
1.0
≤
R
<
2.2
J ( ± 5%)
2.2
≤
R
<
10
10
≤
R
≤
10M
(E24,96)
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature
−55°
C
to + 155
°
C
!
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high–level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it
is used with a steady state voltage that is greater than its rated voltage.
MCR18
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
± (2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F: ± 1%
J: ± 5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 /
−55
/ + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 400V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON
−
25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260 ± 5°C
Soldering time: 10 ± 1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235 ± 5°C
Soldering time: 2.0 ± 0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON
−
0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 95%RH
1.5h: ON
−0.5h:
OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature:
−55°C
to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
± (5.0% + 0.1Ω)
Max. 50mΩ
± (1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
± (1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
± (3.0% +0.1Ω)
Max. 100mΩ
Endurance
(rated load)
± (3.0% +0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
± (3.0% +0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
± (3.0% +0.1Ω)
Max. 100mΩ
Temperature cycling
± (1.0% +0.05Ω)
Max. 50mΩ
Resistance to solvents
± (0.5% +0.05Ω)
Max. 50mΩ
Markings must not be dissolved away.
MCR18
Resistors
!External
dimensions
(Units: mm)
0.5 ± 0.25
No.
Material
Thick dielectric glaze of ruthenium (only silver used for jumper)
Thick film of palladium-silver for primary electrode
3.2 ± 0.15
0.55 ± 0.1
0.5 ± 0.25
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
2
φD
2
E
F
B
2
08
06
04
02
02
04
06
08
1.6 ± 0.15
W
A
B
D
A
2
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
There is a large amount of data passing through the serial port with an uncertain length, but only 128 bytes are read each time. The data is read in a loop. When the specified string is read, the loop...
Mobile phone (client) ---- Computer (server) cmnet dial-up is fine. During the TCP handshake, the server can receive SYN and return SYN+ACK, but cannot receive the last ACK. Then it receives SYN again...
I have some questions about the RCD circuit in the flyback and rectifier power supply. Please discuss and answer the questions.
Below is a flyback RCD circuit
The following is a forward RCD circuit
Wh...
I am currently designing a high-power (over 60W) LED light source, using the LM3433 solution, referring to Ti's circuit. Now I don't know how to deal with the power supply, because the LM3433 requires...
Obtaining real-time and reliable traffic information has always been a bottleneck problem in the development of intelligent transportation systems. The establishment of an intelligent transportatio...[Details]
Engineers who are new to wireless design and wireless product development need to master the basics of
RF measurement
. In many cases, this process is to enable engineers who have been engag...[Details]
Semiconductor devices used in high-end computing (advanced microprocessors) and consumer electronics (graphics and gaming chipsets) devices generally provide data rates up to 6.4Gbps through hig...[Details]
Electrocardiogram is an important means of diagnosing heart disease. However, due to various reasons, it is difficult to capture abnormal electrocardiograms with ordinary electrocardiographs. Although...[Details]
The discipline of HHCE (Home Health Care Engineering) is gradually entering people's lives as people pay more attention to health and telemedicine develops. It advocates the concept of "seeking m...[Details]
In the WTK22wtklibdevicesDefaultColorPhoneDefaultColorPhone.properties file in the WTK directory, there is a line touch_screen=false. Change it to true.
MIDP2.0 has three touch screen methods:...[Details]
Abstract:
Online dynamic signature authentication is increasingly used in various fields, especially in banking and financial systems and personal identification. As the basis of online signa...[Details]
1.AVI
The full name in English is: Audio Video Interleaved. People are very familiar with the AVI format, which is also very common in daily life, and the video quality is also very good. ...[Details]
0 Introduction
The peak value of AC voltage refers to the maximum value (positive peak value) or minimum value (negative peak value) of AC voltage, which is a very important parameter in t...[Details]
With the rapid development of the automobile industry, automotive electronic control systems have attracted widespread social attention. One of the future development directions of automobiles is e...[Details]
Wet etching is the traditional process for removing sacrificial materials from MEMS devices. Point 35 Microstructures, headquartered in Scotland, launched a dry etching module and oxide release techno...[Details]
1 Introduction
With the continuous progress of modern power electronics technology and the development of information technology, inverter power supplies are increasingly widely used in ma...[Details]
It is commonplace today for consumers to use their mobile devices in ways that were unheard of just 10 years ago. Whether browsing the web at their favorite coffee shop, listening to stereo mus...[Details]
0 Introduction
In power electronics technology, the conversion of a DC voltage value into another fixed or adjustable voltage value through a power electronic converter is called DC-DC con...[Details]
With the popularity of Apple iPhone and Nintendo Wii game consoles, accelerometers have been widely used in consumer electronic devices. For example, drop protection in notebooks, automatic screen ...[Details]
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
