EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM7B-02-4120-B-C

Description
Array/Network Resistor, Bussed, Thin Film, 0.08W, 412ohm, 0.1% +/-Tol, -50,50ppm/Cel, 3922,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GM7B-02-4120-B-C Overview

Array/Network Resistor, Bussed, Thin Film, 0.08W, 412ohm, 0.1% +/-Tol, -50,50ppm/Cel, 3922,

GUB-GM7B-02-4120-B-C Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid795887412
package instructionSMT, 3922
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.2
structureMolded
Network TypeBussed
Number of terminals14
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length9.906 mm
Package formSMT
Package width5.588 mm
Rated power dissipation(P)0.08 W
resistance412 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code3922
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Tolerance0.1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Please recommend a unipolar AD conversion chip with few pins
I recently used STM32F767 in a project. The internal AD is 12 bits, which does not meet the requirements. I looked for ADS1274, which has 64 pins, but it has too many pins. I also looked for other AD ...
chenbingjy stm32/stm8
IIR Digital Filter Design - Implementing Arbitrary Order IIR Digital Filters on FPGA
[font=Verdana][font=Verdana]IIR Digital Filter Design - Implementing Arbitrary Order IIR Digital Filters on FPGA[/font][/font] Abstract: This paper introduces a method to implement arbitrary order IIR...
aimyself FPGA/CPLD
Problems with EMP injection into triodes
[color=#333333][font="][size=14px]Why for transistors, some literatures say that under EMP injection, the failure mode of transistors is BE junction short circuit, but some literatures say that BC jun...
xmxxwyh Analog electronics
Ask a simple VHDL question, the signal line is assigned an initial value
I have an IO port P from a CPLD. I want it to be in a certain state (e.g. 0) when it is powered on. After it starts working, another signal S1, S2 triggers the state change of P. For example, P is 0 w...
sioca FPGA/CPLD
USB short body patch specification diagram useful take away
USB short body patch specification diagram...
qwqwqw2088 PCB Design
I don't know how to do the homework assigned by the teacher today. Can anyone give me some advice?
Experiment 3 Priority inheritance 1 Experimental purpose Master the strategy of embedded real-time operating system ?C/OS-II to solve priority inversion - the principle of priority inheritance. 2 Prin...
sanny777 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 321  881  759  1286  2824  7  18  16  26  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号