Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
+3.3V
OE or NC
10nF
1nF
1
6
10nF
OE or NC
2
5
100
3
4
10nF
OE or NC
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
I recently got an embedded board, but I don't understand it. My friend told me that a rookie like me should not try it, because it's hopeless. I'm so depressed. Can you give me some advice? How can I ...
Learning various DSPs from TI can be divided into multiple levels based on the principle of gradual progress. Based on my many years of experience in developing DSPs, I would like to summarize the adv...
Starter Generator/eMotor
The starter generator (including ISG, BISG/iBSG and electric motor) is an integral part of the 48V mild hybrid architecture, maintaining battery charge and providing current t...
When booting from nand, a 4k stepldr will be run first, which will copy the eboot in nand to ram and run. I used uboot before, skipping this limitation. Now I want to debug stepldr, modify stepldr.bib...
Altera's Cyclone V FPGAs deliver the industry's lowest system cost and power consumption, with performance levels that meet your needs for high-volume application differentiation. The family includes ...
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Designing low power circuits while achieving acceptable performance is a difficult task. Doing so in
the RF
bands increases the challenge dramatically. Today, nearly everything has wireless...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
We software engineers love to find the perfect solution to any problem we encounter. But oddly enough, we find that in this particular area, there is no perfect solution. Clever tricks may save som...[Details]
High-voltage switches are important control equipment in power systems and play an important role in the safe operation of power grids. The resistance of the switch conductive loop is an important tec...[Details]
Commonly used power management chips for portable products
●Low Dropout Regulators (LDO Linear Regulators)
LDO
VLDO;
●DC/DC Converters based on inductor energy...[Details]
Infrared technology has been widely used in speed measurement systems, and many products have used infrared technology to achieve vehicle speed measurement, detection and other research. When infra...[Details]
Last week, Microsoft's Windows Phone 8 system was launched with great fanfare and attracted much attention from the industry. However, Nokia, the most staunch supporter of Microsoft's Windows Phone sy...[Details]
1. Problems with the current transformer maintenance method
The current maintenance method for transformers is to deal with defects during regular maintenance and patrol inspections. There...[Details]
Abstract: According to the requirements of pulse carburizing power supply, an IGBT strong drive circuit with high reliability, no signal transmission delay, strong driving ability and other charact...[Details]
The power supply has a great impact on the stability of the system during system operation. A power module with poor quality and stability will not only cause unstable system operation, but also cause...[Details]
There are a few electric car
charging stations
here and there
, which is fine. But if charging stations become common in cities, they will become an eyesore, with long, tangled blac...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
