of "●Precautions" for more information on the minimum applicable
load.
Ratings
Model
D2S-10
models
D2S-5
models
D2S-01
models
Item
Rated voltage
250 VAC
125 VAC
250 VAC
125 VAC
30 VDC
Resistive load
10.1 A
5A
3A
0.1 A
0.1 A
Characteristics
Item
Permissible operating speed
Permissible
operating
frequency
Mechanical
Electrical
Model
D2S-10 models
D2S-5 models
D2S-01 models
0.1 mm to 1 m/s (for pin plunger models)
400 operations/min
60 operations/min
100 MΩ min. (at 500 VDC with insulation tester)
OF 1.47 N models
OF 0.49 N models
-
30mΩ max.
50 mΩ max.
1,000 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
10 to 55 Hz, 1.5 mm double amplitude
OF 1.47 N models
OF 0.49 N models
OF 1.47 N models
OF 0.49 models
1,000 m/s
2
{approx. 100G} max.
500 m/s
2
{approx. 50G} max.
300 m/s
2
{approx. 30G} max.
200 m/s
2
{approx. 20G} max.
10,000,000 operations min.
(60 operations/min)
50,000 operations min.
(30 operations/min)
30,000,000 operations min.
(60 operations/min)
200,000 operations min.
(30 operations/min)
IEC IP40
-25°C to
+85°C
(at ambient humidity of 60% max.)
(with no icing or condensation)
85% max. (for
+5°C
to
+35°C)
Approx. 1.6 g (pin plunger models)
50 mΩ max.
100 mΩ max.
Insulation resistance
Contact resistance
(initial value)
Note. The above rating values apply under the
following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 30 operations/min
Between terminals of the same
polarity
Dielectric
strength * 1
Between current-carrying metal
parts and ground
Between each terminals and
non-current-carrying metal parts
Vibration
resistance * 2
Malfunction
Durability
Shock
resistance
Malfunction * 2
Mechanical
Durability * 3
Electrical
Approved Safety
Standards
The items shown in the "List
of Models"
are not standard approved models.
Consult your OMRON sales
representative for specific models with
standard approvals.
UL (UL1054)/CSA(CSA C22.2 No.55)
Rated
voltage
Model
D2S-10
-
10.1 A
-
D2S-5
5A
3A
-
D2S-01
0.1 A
-
0.1 A
Degree of protection
Ambient operating temperature
Ambient operating humidity
Weight
125 VAC
250 V
30 VDC
Note. The data given above are initial values.
*1. The values for dielectric strength shown are for models with a Separator (refer to "Micro
Switch
Common Accessories").
*2. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel
Position value for lever.
Close or open circuit of the contact is 1ms max.
*3. For testing conditions, consult your OMRON sales representative.
2
D2S
Terminals/Appearances
(Unit: mm)
●Solder
terminals
3.3
±0.1
2
7.3
8.8
±0.2
9.5
±0.1
16.1
±0.2
1.6
3.2
0.5
6.4
±0.2
5.15
1.85
8.8
±0.2
9.5
±0.1
16.1
±0.2
0.8
1.2
6.4
±0.2
0.5
1.3
Subminiature Basic Switch
Mounting Holes
(Unit: mm)
2-2.4 dia. mounting holes or
M2.3 screw holes
●Self-clinching
PCB terminals
3.3
±0.1
2
1.8
±0.1
3.9
9.5
±0.1
3-1.6 dia.holes
5.15
1.85
<PCB Mounting Dimensions (Reference)>
3-1.35
1.5 dia.
D
2
S
8.8
±0.2
16.1
±0.2
PCB's thickness t
1.6mm
Dimensions
(Unit: mm)
and Operating Characteristics
The following figures show models with self-clinching PCB terminals. For the solder terminals, refer to "Terminals/Appearances".
The
@
is replaced with the code for the terminal that you need. See the "List
of Models"
for available combinations of models.
●Pin
plunger
D2S-10@
D2S-5@
D2S-5-F@
D2S-01@
D2S-01-F@
5.3
A
2.35
±0.05
dia.
7.5
±0.1
1.8
2.35
±0.05
dia.
PT
3.6
Model
Operating
characteristics
1.8
±0.1
7
2
7.7
OP
D2S-10@
D2S-5@
D2S-01@
D2S-5-F@
D2S-01-F@
3.3
±0.1
3.9
Operating Force
Releasing Force
OF
RF
Max. 1.47 N {150 gf} 0.49 N {50 gf}
Min. 0.25 N {25 gf} 0.04 N {4 gf}
0.7 mm
0.4 mm
0.1 mm
8.4±0.25 mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
Pretravel
PT Max.
Overtravel
OT Min.
Movement Differential MD Max.
Operating Position
OP
19.8
±0.2
●Hinge
lever
D2S-10L@
D2S-5L@
D2S-5L-F@
D2S-01L@
D2S-01L-F@
t 0.3 *
14.5
A
2.35
±0.05
dia.
3.6
Model
FP
2.35
±0.05
dia.
7
2
7.7
OP
1.8
±0.1
Operating
characteristics
Operating Force
Releasing Force
OF
RF
D2S-10L@
D2S-5L@
D2S-01L@
D2S-5L-F@
D2S-01L-F@
0.18 N {18 gf}
0.02 N {2 gf}
3.3
±0.1
3.9
Max. 0.49 N {50 gf}
Min. 0.06 N {6 gf}
Overtravel
OT Min.
Movement Differential MD Max.
0.5
1.3
1.0 mm
0.8 mm
13.6 mm
9.4±0.8mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
* Stainless-steel lever
6.4
±0.2
Free Position
Operating Position
FP Max.
OP
19.8
±0.2
●Simulated
roller lever
D2S-10L13@
D2S-5L13@
D2S-5L13-F@
D2S-01L13@
D2S-01L13-F@
15.8
t 0.3 *
A
R1.3
3.6
2.35
±0.05
dia.
FP
Operating
characteristics
Operating Force
Releasing Force
Model D2S-10L13@
D2S-5L13@
D2S-01L13@
OF Max.
RF Min.
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L13-F@
D2S-01L13-F@
0.18 N {18 gf}
0.02 N {2 gf}
2.35
±0.05
dia.
OP
7
2
7.7
3.3
±0.1
3.9
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
1.8
±0.1
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
15.5 mm
11.4±0.8 mm
0.5
1.3
*Stainless-steel lever
6.4
±0.2
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
3
D2S
●Hinge
roller lever
D2S-10L2@
D2S-5L2@
D2S-5L2-F@
D2S-01L2@
D2S-01L2-F@
14.5
t=0.3 *1
2.35
±0.05
dia.
FP
OP
2.35
±0.05
dia.
7
2
7.7
3.3
±0.1
3.9
1.8
±0.1
A
4.8x3.2 *2 dia.
Subminiature Basic Switch
Model
Operating
characteristics
Operating Force
Releasing Force
OF Max.
RF Min.
D2S-10L2@
D2S-5L2@
D2S-01L2@
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L2-F@
D2S-01L2-F@
0.18 N {18 gf}
0.02 N {2 gf}
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
19.3 mm
15.1±0.8 mm
D
2
S
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
*1. Stainless-steel lever
*2. Polyacetal resin roller
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Precautions
★
Please refer to "Basic Switches Common Precautions" for correct use.
Cautions
●Soldering
When using automatic soldering baths, we recommend soldering
at 260±5°C within 5 seconds. Make sure that the liquid surface
of the solder does not flow over the edge of the board.
When soldering terminals manually, complete the soldering at
the iron tip temperature between 350 to 400°C within 3 seconds,
and do not apply any external force for 1 minute after soldering.
When applying solder, keep the solder away from the case of the
Switch and do not allow solder or flux to flow into the case.
Correct Use
●Mounting
Use M2.3 mounting screw with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 N·m {2.3 to 2.7 kgf·cm}.
●Using
Micro Loads
Using a model for ordinary loads to open or close the contact of
a micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the following operating range, if inrush
current occurs when the contact is opened or closed, it may
increase the contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary. The N-level
reference value applies for the minimum applicable load. This
value indicates the malfunction reference level for the reliability
level of 60% (λ
60
).
(JIS C5003)
The equation,
λ
60
=0.5×10
-6
/operations indicates that the
1
estimated malfunction rate is less than
2,000,000
operations with
a reliability level of 60%.
Voltage (V)
0.16 mA
26 mA
100 mA
30
24
Normal load
type
Operating
range
D2S-5
D2S-10
Micro load type
Operating range
D2S-01
12
5
0
0.1
1 mA
1
10
100 mA 160 mA
100
1,000
Current (mA)
4
D2S
Subminiature Basic Switch
D
2
S
•
Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
•
Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
[i=s]This post was last edited by lonerzf on 2014-2-23 07:17[/i] I have two doubts after reading the I2C document. Please help me solve my doubts, thank you. :congratulate: [b][size=4]Confusion 1[/siz...
[hide]1. The nominal input voltage range of the driver chip should meet the requirements of DC 8~40V to cover a wide range of applications. The withstand voltage should preferably be greater than 45V....
When I was debugging a program with CCS2000, I selected F2812 Simulator at the beginning of the setup. The original program was written in C, and the header file used #include \"register.h\" I don't k...
I need this for my graduation project. The topic of my graduation project is voice playback based on stm32. I want to realize DA conversion through pwm, but I don’t know how to write the program and h...
With the booming electronics industry, vision systems have become a leader in the electronics automation sector. However, the delicate nature of electronic products often affects product yields due...[Details]
On August 24th, media outlets reported, citing sources, that NavInfo, a listed company on the A-share market, is nearing completion in its acquisition of the intelligent driving c...[Details]
According to foreign media reports, researchers at the University of Surrey have developed an artificial intelligence system that can accurately locate the location of equipment in densely populate...[Details]
Zos Automotive Research Institute released the "2025
Smart Cockpit
Tier 1 Research Report (Domestic Edition)."
This report analyzes the operating conditions of more than a dozen ...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
HTTP is the abbreviation of Hypertext Transfer Protocol. It is an application protocol based on TCP/IP communication protocol used to transmit HTML and image files. It is an application-level objec...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Shanghai, China, August 21, 2025 –
Toshiba Electronic Devices & Storage Corporation (“Toshiba”) today announced the launch of the TLX9161T
, an automotive photorelay in a compact SO12L-T pa...[Details]
In camera and display systems, the demand for high-performance and low-power data interfaces is driving continuous technological evolution. The evolution of MIPI D-PHY and MIPI C-PHY clearly ...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
On August 20, Reuters reported that two sources revealed that U.S. Commerce Secretary Howard Lutnick is exploring the possibility of using CHIPS Act funds in exchange for equity stakes in chip manu...[Details]
Touch-sensitive steering wheel buttons have appeared in some car models in recent years. Initially marketed as "futuristic and intelligent," these features have proven problematic in practice. Volk...[Details]
From the arms that simply and repeatedly carry heavy objects on the assembly line, to the two-arm "blue-collar" robots that easily plug and unplug circuit harnesses, to the humanoid robot "clerks" ...[Details]
Smart bracelets, as a relatively popular product form in the past two years, have attracted more and more attention from people. At the same time, they have also brought about some changes in the e...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
