of "●Precautions" for more information on the minimum applicable
load.
Ratings
Model
D2S-10
models
D2S-5
models
D2S-01
models
Item
Rated voltage
250 VAC
125 VAC
250 VAC
125 VAC
30 VDC
Resistive load
10.1 A
5A
3A
0.1 A
0.1 A
Characteristics
Item
Permissible operating speed
Permissible
operating
frequency
Mechanical
Electrical
Model
D2S-10 models
D2S-5 models
D2S-01 models
0.1 mm to 1 m/s (for pin plunger models)
400 operations/min
60 operations/min
100 MΩ min. (at 500 VDC with insulation tester)
OF 1.47 N models
OF 0.49 N models
-
30mΩ max.
50 mΩ max.
1,000 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
10 to 55 Hz, 1.5 mm double amplitude
OF 1.47 N models
OF 0.49 N models
OF 1.47 N models
OF 0.49 models
1,000 m/s
2
{approx. 100G} max.
500 m/s
2
{approx. 50G} max.
300 m/s
2
{approx. 30G} max.
200 m/s
2
{approx. 20G} max.
10,000,000 operations min.
(60 operations/min)
50,000 operations min.
(30 operations/min)
30,000,000 operations min.
(60 operations/min)
200,000 operations min.
(30 operations/min)
IEC IP40
-25°C to
+85°C
(at ambient humidity of 60% max.)
(with no icing or condensation)
85% max. (for
+5°C
to
+35°C)
Approx. 1.6 g (pin plunger models)
50 mΩ max.
100 mΩ max.
Insulation resistance
Contact resistance
(initial value)
Note. The above rating values apply under the
following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 30 operations/min
Between terminals of the same
polarity
Dielectric
strength * 1
Between current-carrying metal
parts and ground
Between each terminals and
non-current-carrying metal parts
Vibration
resistance * 2
Malfunction
Durability
Shock
resistance
Malfunction * 2
Mechanical
Durability * 3
Electrical
Approved Safety
Standards
The items shown in the "List
of Models"
are not standard approved models.
Consult your OMRON sales
representative for specific models with
standard approvals.
UL (UL1054)/CSA(CSA C22.2 No.55)
Rated
voltage
Model
D2S-10
-
10.1 A
-
D2S-5
5A
3A
-
D2S-01
0.1 A
-
0.1 A
Degree of protection
Ambient operating temperature
Ambient operating humidity
Weight
125 VAC
250 V
30 VDC
Note. The data given above are initial values.
*1. The values for dielectric strength shown are for models with a Separator (refer to "Micro
Switch
Common Accessories").
*2. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel
Position value for lever.
Close or open circuit of the contact is 1ms max.
*3. For testing conditions, consult your OMRON sales representative.
2
D2S
Terminals/Appearances
(Unit: mm)
●Solder
terminals
3.3
±0.1
2
7.3
8.8
±0.2
9.5
±0.1
16.1
±0.2
1.6
3.2
0.5
6.4
±0.2
5.15
1.85
8.8
±0.2
9.5
±0.1
16.1
±0.2
0.8
1.2
6.4
±0.2
0.5
1.3
Subminiature Basic Switch
Mounting Holes
(Unit: mm)
2-2.4 dia. mounting holes or
M2.3 screw holes
●Self-clinching
PCB terminals
3.3
±0.1
2
1.8
±0.1
3.9
9.5
±0.1
3-1.6 dia.holes
5.15
1.85
<PCB Mounting Dimensions (Reference)>
3-1.35
1.5 dia.
D
2
S
8.8
±0.2
16.1
±0.2
PCB's thickness t
1.6mm
Dimensions
(Unit: mm)
and Operating Characteristics
The following figures show models with self-clinching PCB terminals. For the solder terminals, refer to "Terminals/Appearances".
The
@
is replaced with the code for the terminal that you need. See the "List
of Models"
for available combinations of models.
●Pin
plunger
D2S-10@
D2S-5@
D2S-5-F@
D2S-01@
D2S-01-F@
5.3
A
2.35
±0.05
dia.
7.5
±0.1
1.8
2.35
±0.05
dia.
PT
3.6
Model
Operating
characteristics
1.8
±0.1
7
2
7.7
OP
D2S-10@
D2S-5@
D2S-01@
D2S-5-F@
D2S-01-F@
3.3
±0.1
3.9
Operating Force
Releasing Force
OF
RF
Max. 1.47 N {150 gf} 0.49 N {50 gf}
Min. 0.25 N {25 gf} 0.04 N {4 gf}
0.7 mm
0.4 mm
0.1 mm
8.4±0.25 mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
Pretravel
PT Max.
Overtravel
OT Min.
Movement Differential MD Max.
Operating Position
OP
19.8
±0.2
●Hinge
lever
D2S-10L@
D2S-5L@
D2S-5L-F@
D2S-01L@
D2S-01L-F@
t 0.3 *
14.5
A
2.35
±0.05
dia.
3.6
Model
FP
2.35
±0.05
dia.
7
2
7.7
OP
1.8
±0.1
Operating
characteristics
Operating Force
Releasing Force
OF
RF
D2S-10L@
D2S-5L@
D2S-01L@
D2S-5L-F@
D2S-01L-F@
0.18 N {18 gf}
0.02 N {2 gf}
3.3
±0.1
3.9
Max. 0.49 N {50 gf}
Min. 0.06 N {6 gf}
Overtravel
OT Min.
Movement Differential MD Max.
0.5
1.3
1.0 mm
0.8 mm
13.6 mm
9.4±0.8mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
* Stainless-steel lever
6.4
±0.2
Free Position
Operating Position
FP Max.
OP
19.8
±0.2
●Simulated
roller lever
D2S-10L13@
D2S-5L13@
D2S-5L13-F@
D2S-01L13@
D2S-01L13-F@
15.8
t 0.3 *
A
R1.3
3.6
2.35
±0.05
dia.
FP
Operating
characteristics
Operating Force
Releasing Force
Model D2S-10L13@
D2S-5L13@
D2S-01L13@
OF Max.
RF Min.
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L13-F@
D2S-01L13-F@
0.18 N {18 gf}
0.02 N {2 gf}
2.35
±0.05
dia.
OP
7
2
7.7
3.3
±0.1
3.9
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
1.8
±0.1
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
15.5 mm
11.4±0.8 mm
0.5
1.3
*Stainless-steel lever
6.4
±0.2
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
3
D2S
●Hinge
roller lever
D2S-10L2@
D2S-5L2@
D2S-5L2-F@
D2S-01L2@
D2S-01L2-F@
14.5
t=0.3 *1
2.35
±0.05
dia.
FP
OP
2.35
±0.05
dia.
7
2
7.7
3.3
±0.1
3.9
1.8
±0.1
A
4.8x3.2 *2 dia.
Subminiature Basic Switch
Model
Operating
characteristics
Operating Force
Releasing Force
OF Max.
RF Min.
D2S-10L2@
D2S-5L2@
D2S-01L2@
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L2-F@
D2S-01L2-F@
0.18 N {18 gf}
0.02 N {2 gf}
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
19.3 mm
15.1±0.8 mm
D
2
S
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
*1. Stainless-steel lever
*2. Polyacetal resin roller
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Precautions
★
Please refer to "Basic Switches Common Precautions" for correct use.
Cautions
●Soldering
When using automatic soldering baths, we recommend soldering
at 260±5°C within 5 seconds. Make sure that the liquid surface
of the solder does not flow over the edge of the board.
When soldering terminals manually, complete the soldering at
the iron tip temperature between 350 to 400°C within 3 seconds,
and do not apply any external force for 1 minute after soldering.
When applying solder, keep the solder away from the case of the
Switch and do not allow solder or flux to flow into the case.
Correct Use
●Mounting
Use M2.3 mounting screw with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 N·m {2.3 to 2.7 kgf·cm}.
●Using
Micro Loads
Using a model for ordinary loads to open or close the contact of
a micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the following operating range, if inrush
current occurs when the contact is opened or closed, it may
increase the contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary. The N-level
reference value applies for the minimum applicable load. This
value indicates the malfunction reference level for the reliability
level of 60% (λ
60
).
(JIS C5003)
The equation,
λ
60
=0.5×10
-6
/operations indicates that the
1
estimated malfunction rate is less than
2,000,000
operations with
a reliability level of 60%.
Voltage (V)
0.16 mA
26 mA
100 mA
30
24
Normal load
type
Operating
range
D2S-5
D2S-10
Micro load type
Operating range
D2S-01
12
5
0
0.1
1 mA
1
10
100 mA 160 mA
100
1,000
Current (mA)
4
D2S
Subminiature Basic Switch
D
2
S
•
Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
•
Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
In electronic circuits, we often see three different symbols: VCC, VDD and VSS. What is the difference between them? [/font][/color][/font][/p][p=25, null, left][font=Tahoma,][color=#4e4e4e][font=Aria...
For example, taskA is defined in moduleA, and moduleB and moduleA may be nested or called in parallel by high-level modules. Then can moduleB call taskA?...
Hello everyone, when I compile a code, a stack overflow warning appears.
Theoretically, my data segment is:
map file 6 152 bytes of CODE memory 1 268 bytes of DATA memory (+ 56 absolute )463 bytes of ...
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
Teletrac Navman has launched the Multi IQ dashcam, a cloud-based solution designed for large commercial vehicle operators. It connects up to five cameras to cover the vehicle's interior, sides, and...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
In camera and display systems, the demand for high-performance and low-power data interfaces is driving continuous technological evolution. The evolution of MIPI D-PHY and MIPI C-PHY clearly ...[Details]
Compiled from semiengineering
The industry is increasingly concerned about power consumption in AI, but there are no simple solutions. This requires a deep understanding of software and ...[Details]
A Beijing chemical project utilizes a distributed control system (DCS). The master control system primarily uses the Modbus protocol, while the remote field devices utilize the PROFIBUS-DP protocol...[Details]
Currently, PLCs are widely used in various industries, including special machine tools, machine tools, control systems, building automation, steel, petrochemicals, electricity, building materials, ...[Details]
The number of new energy vehicles in use is increasing, and there are multiple choices available. New energy vehicles can be divided into hybrid and pure electric, and the types of hybrid include m...[Details]
Chip architecture licensing company ARM has hired Amazon's AI chip chief Rami Sinno to help advance its plan to develop its own complete chip, people familiar with the matter said, according to Reu...[Details]
According to reports from Xinhua News Agency, Tianjin University official website and other media, Chinese researchers have recently broken through the bottleneck of energy density and application ...[Details]
1. Introduction to power amplifier circuit
1. Generally speaking, the main function of a power amplifier circuit is to allow the load to obtain maximum power without distorting the signal or c...[Details]
We often notice that some safety light curtains have EDM function. What does EDM mean here? What is its function?
The full name of EDM is External Device Monitor, which means external device m...[Details]
Robots are rapidly being deployed in diverse scenarios. Flexible, easy-to-use, and fast-to-deploy robots can be quickly adapted to diverse application scenarios across various industries, making th...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
