All temperatures refer to topside of the package, measured on the package body surface.
260°C Reflow Profile
W
&
W &
3°C/seconds max.
150°C
200°C
60-180 seconds
3°C/seconds max.
217°C
60-150 seconds
max 260°C
Time within 5°C of actual
Peak Temperature (tp)
Ramp-down Rate
6°C/seconds max.
20-40 seconds max.
W
&
W &
8 minutes max.
Average ramp-up rate (TL to TP)
Preheat - Temperature min Tsmin
- Temperature min Tsmax
- Time (min to max) (ts)
Tsmax to TL -Ramp-up Rate
Time maintained above - Temperature (TL)
- Time (TL)
Peak Temperature (Tp)
E
Time 25°C to Peak Temperature
Time maintained above
- Temperature (TL)
- Time (tL)
217°C
60-150 seconds
All temperatures refer to topside of the package, measured on the package body surface.
4 of 5
Ordering Information
EX - 401 0 - D A P - 108 0 - 10M0000000
Frequency
Frequency Control
20
Configuration
Thru-hole
Stability Code
Supply Voltage
508: ±50ppb
758: ±75ppb
107: ±100ppb
6: Fixed Frequency (+5 dBm)
7: Electrical Tuning (+5 dBm)
d
d
^
Z
Z
^
&
&
d
^
d
108 (+/-10ppb)
208 (+/-20ppb)
308 (+/-30ppb)
508 (+/-50ppb)
758 (+/-75ppb)
107 (+/-100ppb)
A: -55°C to +85°C E: -40°C to +85°C J: -20°C to +70°C P: 0°C to +50°C
10-20MHz
10-20MHz
10-50MHz
10-80MHz
10-100MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
Aging Table
Temperature Range and Stability Table
Notes:
Stability/Temperature A: -55°C to +85°C
E: -40°C to +85°C
J: -20°C to +70°C
1.
108
(+/-10ppb)
frequencies.
10-30MHz
2.
208 (+/-20ppb)
10-30MHz
10-30MHz
308 (+/-30ppb) 10-30MHz
10-30MHz
10-30MHz
10-30MHz
4.
Subject to technical modification.
Contact factory for availability.
P: 0°C to +50°C
For Additional Information, Please Contact
USA:
Vectron International
Europe:
Vectron International
Asia:
Vectron International
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
I am familiar with C development, but I have never developed in VxWorks. What is the difference between developing C in VxWorks and developing C in Windows or Linux? Does VxWorks use its own API or is...
I made a low-power device. When I tested the power consumption, I found that there was still about 125uA of current in sleep mode. Then I checked the cause and found that it was the power consumption ...
Renesas Synergy S1 series microcontroller (MCU) R7FS1JA is a new product launched by Renesas. It has 48MHz Arm Cortex-M23 core, and the resources are very rich, 16bit adc, 24bit adc, 12bit DAC, "][siz...
Could you please tell me, when a certain timer of MSP430F149, such as timer A, is used as PWM output, it can output PWM waves of different frequencies?For example: Can P1.1, P1.2, and P1.3 output PWM ...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
1. The composition and structure of mobile phone lithium battery
Mobile phone lithium batteries are mainly composed of plastic shell upper and lower covers, lithium battery cells, protection c...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Real-time operating system RTOS
京公网安备 11010802033920号
EEWORLD
