All temperatures refer to topside of the package, measured on the package body surface.
260°C Reflow Profile
W
&
W &
3°C/seconds max.
150°C
200°C
60-180 seconds
3°C/seconds max.
217°C
60-150 seconds
max 260°C
Time within 5°C of actual
Peak Temperature (tp)
Ramp-down Rate
6°C/seconds max.
20-40 seconds max.
W
&
W &
8 minutes max.
Average ramp-up rate (TL to TP)
Preheat - Temperature min Tsmin
- Temperature min Tsmax
- Time (min to max) (ts)
Tsmax to TL -Ramp-up Rate
Time maintained above - Temperature (TL)
- Time (TL)
Peak Temperature (Tp)
E
Time 25°C to Peak Temperature
Time maintained above
- Temperature (TL)
- Time (tL)
217°C
60-150 seconds
All temperatures refer to topside of the package, measured on the package body surface.
4 of 5
Ordering Information
EX - 401 0 - D A P - 108 0 - 10M0000000
Frequency
Frequency Control
20
Configuration
Thru-hole
Thru-hole with Solder Coated Leads
Supply Voltage
508: ±50ppb
758: ±75ppb
107: ±100ppb
Stability Code
d
d
^
Z
Z
^
&
&
d
^
d
108 (+/-10ppb)
208 (+/-20ppb)
308 (+/-30ppb)
508 (+/-50ppb)
758 (+/-75ppb)
107 (+/-100ppb)
A: -55°C to +85°C E: -40°C to +85°C J: -20°C to +70°C P: 0°C to +50°C
10-20MHz
10-20MHz
10-50MHz
10-80MHz
10-100MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
Aging Table
Temperature Range and Stability Table
Notes:
Stability/Temperature A: -55°C to +85°C
E: -40°C to +85°C
J: -20°C to +70°C
1.
108
(+/-10ppb)
frequencies.
10-30MHz
2.
208 (+/-20ppb)
10-30MHz
10-30MHz
308 (+/-30ppb) 10-30MHz
10-30MHz
10-30MHz
10-30MHz
4.
Subject to technical modification.
Contact factory for availability.
P: 0°C to +50°C
For Additional Information, Please Contact
USA:
Vectron International
Europe:
Vectron International
Asia:
Vectron International
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
I applied for an innovation project at school. I want to make a fingerprint recognition system. I just need to input and verify the fingerprint, and then alarm if the fingerprint is wrong. Has anyone ...
Great God, the fuse position was not changed when the avr was used, and the download line was not lost during the burning process, but it was still locked. It always entered the programming mode error...
3.3V power supply, I could download the program and run it at first, but it would get hot after running for a while and finally burned out. I have burned 5 of them, God help me...
Question: 8-bit bitmap mov r0, #0x3F0 According to ARM Architecture and Programming, page 24, it is said that the smallest rotate_imm encoding method should be used. So the following two encoding meth...
Address mapping error. The error is as follows: ERROR: C:\WINCE600\PLATFORM\SBC8100\SRC\DRIVERS\TOUCH\.\touchscreen.cpp line 182 : For PRCMregs: VirtualAlloc failed! The physical address mapping virtu...