BW2F-180JTW datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> BW2F-180JTW

BW2F-180JTW: DescriptionFixed Resistor - Fusible, 2W, 18ohm, 5% +/-Tol, 200ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT; CategoryPassive components The resistor; File Size65KB，1 Pages; ManufacturerRCD Components Inc.; Websitehttp://www.rcdcomponents.com/; Environmental Compliance

Download Datasheet Parametric View All

BW2F-180JTW Overview

Fixed Resistor - Fusible, 2W, 18ohm, 5% +/-Tol, 200ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

BW2F-180JTW Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Objectid	1733981255
package instruction	AXIAL LEADED, ROHS COMPLIANT
Reach Compliance Code	compliant
ECCN code	EAR99
YTEOL	7
Other features	FLAMEPROOF
structure	Flameproof
JESD-609 code	e3
Lead diameter	0.8 mm
Lead length	26 mm
Manufacturer's serial number	BW
Installation features	THROUGH HOLE MOUNT
Number of terminals	2
Maximum operating temperature	165 °C
Minimum operating temperature	-55 °C
Package diameter	4.1 mm
Package length	11.4 mm
Package shape	TUBULAR PACKAGE
Package form	Axial
method of packing	TR
Rated power dissipation(P)	2 W
resistance	18 Ω
Resistor type	FIXED RESISTOR - FUSIBLE
series	BW
surface mount	NO
Temperature Coefficient	200 ppm/°C
Terminal surface	Matte Tin (Sn)
Terminal shape	WIRE
Tolerance	5%
Operating Voltage	300 V

BW2F-180JTW Preview

FUSIBLE FILM RESISTORS,

GENERAL PURPOSE 1/8 WATT to 3 WATT

RESISTORS CAPACITORS COILS DELAY LINES

BW/MBW SERIES

RoHS

Term.W is

RoHS

compliant

& 260°C

compatible

BW Series - Axial Lead

MBW Series - SM MELF

Industry’s widest selection of fusible film resistors -

1/8W to 3W, .1Ω to 24KΩ, 1% to 5%, leaded & surface mount

Low cost, quick delivery (available on

SWIFT

program)

Flameproof (UL94V0), surface-mount versions available

Low Cost Circuit Protection!

RCD pioneered fusible film resistors in the early 1970’s as a

low cost approach to circuit protection in case of overload or

component failure. The component is designed to act as a

conventional resistor under normal operating conditions, but

open quickly under fault conditions. Series BW meets the

requirements of EIA RS-325 and can be useful in eliminating

circuit board damage and fire hazards. Standard fusing

characteristics can be altered to customer requirements.

OPTIONS

Modified fusing characteristics (fast blow, slow blow, etc.)

Increased pulse capability (Option P)

Dozens of additional options are available...

Mil-spec screening/burn-in, special marking, non-standard

values, custom lead forming, increased power or voltage, etc.

Customized components are an RCD specialty!

←

→←

→

↓

↑

↓

←

→

MBW

↓

Dimensions BW Series (Axial Lead)

RCD Type

BW1/8F

BW1/4F, MBW1/4F

BW1/2F, MBW1/2F

BW1/2FS, MBW1/2FS

BW1F, MBW1FS

BW2F, MBW2F

BW3F, MBW3F

Dimensions MBW (MELF)

(Min.)

± .012[.3]

(Max.)

N/A

.118 [3]

.197 [5]

.040 [1]

.080 [2]

.154 [3.9] .060 [1.5]

(Min.)

Wattage Resistance

Rating

Range

1/8W

1/4W

1/2W

1.0W

2.0W

3.0W

Voltage

Rating

1, 2

200V

250V

300V

350V

± .032 [.8]

.145 [3.7]

.250 [6.4]

.354 [9.0]

.250 [6.4]

.375 [9.5]

.450 [11.4]

1/2

± .024 [.6]

.067 [1.7]

.090 [2.3]

.128 [3.3]

.090 [2.3]

.135 [3.4]

.162 [4.1]

±.003 [.07]

1Ω to 10K

0.1

Ω

to 10K

0.1

Ω

to 24K

0.2

Ω

to 20K

0.1

Ω

to 24K

0.1

Ω

to 24K

0.1

Ω

to 24K

.020 [.5] 1.00 [25]

.022 [.55] 1.02 [26] .256 [6.5]

.025 [.6] 1.02 [26] .374 [9.5]

.022 [.55] 1.02 [26] .256 [6.5]

.026 [.65] 1.02 [26] .374 [9.5]

.031[.8]

1.02 [26] .441[ 11.2]

.60±.062[15.2±1.6] .22±.032[5.6±.8]

1.37 [35] .598 [15.2] .220 [5.6]

Expanded range available

Maximum working voltage is determined by E = (PR) , E should not exceed value listed.

FUSING CHARACTERISTICS

FUSING TIME (SECONDS, TYP.)

1/2F, FS

1F, 1FS

1/8F

100

APPLIED POWER (WATTS)

APPLICATION NOTES:

1. Fault level must be suitable to safely open the resistor quickly, especially surface mount

MBW models. If insufficent, the resistor may reach elevated temp. For this reason, the

fusing overload must be relatively large compared to rated W, 20 to 50x is common for

most axial-lead applications, 40 to 100x for most SM circuits. SM fusing times vary due to

mounting geometry/materials, so each application needs to be evaluated by user. The fault

condition must be at least equal to the minimum W indicated in each of the above curves,

and preferably double for SM applications. Fusing may still occur at W levels below the

levels graphed above but not consistently (fast-blow models available). Don’t exceed volt

rating or 200x W rating, whichever is less (increased levels available).

2. For customized models, complete RCD’s Fuse Questionnaire or advise the desired fusing

wattage or current, min.& max. blow time, continuous wattage, ambient temp., pulse

conditions, physical constraints, voltage to be interrupted, frequency, etc.

3. Maintain clearance from any heat-sensitive or flammable materials.

4. Fusing times vary depending on resistance value. Typical fusing times are given above

for 1Ω - 3.9K. Low values tend to fuse slower. Consult factory for assistance.

5. Residual resis. is

≥50x

initial value after fusing at 20x rated W (30x for BW1/8F & MBW)

6. Verify selection by evaluating under the full range of fault conditions. Place resistors

inside a protective case when testing.

TYPICAL PERFORMANCE

Temperature Coefficient

Load Life Stability

Operating Temp. Range

Power Derating

Dielectric Strength

200ppm/°C

-55 to +165°C

0.71%/°C >25°C

500V (300V BW1/8F)

P/N DESIGNATION:

BW1F

RCD Type

Options

(leave blank if standard)

1/4F

↑

Inch [mm]

↑

- 101 J T W

Resis.Code 1%:

3 signif. figures & multiplier,

(R100=.1Ω,1R00=1Ω,10R0=10Ω,1000=100Ω, etc.)

Resis.Code 2%-10%:

2 signif. figures & multiplier,

(R10=0.1Ω, 1R0=1Ω, 100=10Ω, 101=100Ω, etc.)

Tolerance:

J=5% (std.) G=2%, F=1%

Packaging:

B=Bulk, T=Tape & Reel

Termination:

W = Lead-free, Q = Tin/Lead

(leave blank if either acceptable)

RCD Components Inc,

520 E.Industrial Park Dr, Manchester, NH, USA 03109

rcdcomponents.com

Tel: 603

669

0054 Fax: 603

669

5455 Email:sales@rcdcomponents.com

FA037D Sale of this product is in accordance with GF-061. Specifications subject to change without notice.

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Classic car battery charging circuit diagram

Full-featured subwoofer power amplifier 02

Object departure alarm circuit

Simple temperature program controller circuit

Three-limit four-state circuit diagram

Telephone electronic code lock circuit diagram

The best introductory material for LM3811: Download the best introductory information for LM3S811 for beginners!...; qwertyuiop11111 Microcontroller MCU

Some problems with CMD files!: I am a novice and just started to learn DSP! Recently I have been learning CMD files and have read some routine CMD files. I don’t understand some parts. I hope those who know can give me some advice....; hoboq DSP and ARM Processors

Design of high-speed data transmission terminal in GPS vehicle monitoring and dispatching system: This paper introduces the design and development of a high-speed GPS data transmission terminal used for GPS vehicle monitoring and dispatching. The terminal has half-duplex communication, GMSK data m...; zzzzer16 Automotive Electronics

Heroes, come and see, a small problem: I am using sqlce 3.5. I directly installed sqlce.wce5.armv4i.CAB to the simulator, but when creating a database, a problem occurred when running the following line of code. hr = CoCreateInstance(CLSID...; hongliang Embedded System

Road Design Talk 11: The Great Leap Forward of the Internet of Things: Once upon a time, with Premier Wen's visit to Wuxi in 2009, an unfamiliar term resounded throughout the country: the Internet of Things. As a result, China Mobile, the Chinese Academy of Sciences, and...; linda_xia Analog electronics

LWIP static IP configuration problem: [i=s]This post was last edited by yanhy on 2015-4-26 16:42[/i] [color=#000]Before modification:[/color][b]lwIPInit(g_ui32SysClock, pui8MACArray, 0, 0, 0, IPADDR_USE_DHCP);[/b] [color=#000]The dynamic ...; yanhy Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components