EEWORLDEEWORLDEEWORLD

Part Number

Search

OPL530-OCB

Description
photo IC sensors photologic sensor
CategoryLED optoelectronic/LED   
File Size428KB,8 Pages
ManufacturerAll Sensors
Environmental Compliance
Download Datasheet Parametric View All

OPL530-OCB Online Shopping

Suppliers Part Number Price MOQ In stock  
OPL530-OCB - - View Buy Now

OPL530-OCB Overview

photo IC sensors photologic sensor

OPL530-OCB Parametric

Parameter NameAttribute value
ManufactureTT electronics
Product CategoryPhoto IC Sensors
RoHSYes
ProducPhoto IC
Number of Channels1 Channel
Output TypeOpen Collec
Operating Supply Voltage4.5 V to 16 V
Supply Curre2.7 mA
High Level Output Curre0.1 uA
Rise Time50 ns
Fall Time20 ns
Propagation Delay Time3 us
Maximum Operating Temperature+ 85 C
Minimum Operating Temperature- 40 C
Factory Pack Quantity50
Low Level Output Voltage0.2 V
Maximum Power Dissipati90 mW
Mounting StyleThrough Hole
Wavelength935 nm
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551,
OPL560, OPL561, OPL562, OPL563
Features:
Choice of four output options in low-cost side-looking package
Choice of two sensitivity options (OPL560/561/562/563)
High noise immunity
Direct TTL/LSTTL CMOS interface
Data rates to 250 kBaud for all except OPL560 series (200 kBaud)
Low power consumption
Product Photo Here
Description:
All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and NPN output
transistor on a single silicon chip.
OPL560
chips also include a voltage regulator on the chip. All devices in the
series have a Photologic® chip that is encapsulated in a molded plastic side-looking package with an integral lens
(recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical coupling, combined
with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers high
immunity to noise on input and V
CC
.
OPL530, OPL531, OPL535
and
OPL536
include a 10 K
pull-up resistor (R
L
) from output to V
CC
. These
components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of
irradiance levels.
OPL550
and
OPL551
devices feature TTL/LSTTL compatible logic level output which can drive
up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall
times of 25 nanoseconds.
OPL560, OPL561, OPL562
and
OPL563
devices feature TTL/LSTTL compatible logic
level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V.
OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562
and
OPL563
are mechanically and spectrally
matched to OP140 and OP240 LEDs.
OPL535
and
OPL536
are mechanically and spectrally matched to OP145
and OP245 series LEDs.
Applications:
Non-contact reflective
object sensor
Assembly line automation
Machine automation
Machine safety
End of travel sensor
Door sensor
Base Part Number
OPL530
OPL531
OPL535
OPL536
OPL550
OPL551
OPL560
OPL561
OPL562
OPL563
Package
Output Type - with Light
Internal 10K - High
Internal 10K - Low
Internal 10K - High
Internal 10K - Low
Input Power Range
(mW/cm
2
) [Min/Max]
-
A
B
0.08/.40
0.08/.25
Recessed
Lens
Totem Pole - High
Totem Pole - Low
Totem Pole - High
Totem Pole - Low
Totem Pole - High
Totem Pole - Low
OC = Open Collector Output
0.25/2.4
0.25/2.5
0.09/.55
0.25/1.4
0.25/1.5
0.09/.36
0.20/0.40
0.025/.23
0.025/.14
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 09/08
Page 1 of 8
OPTEK Technology Inc. —
1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
USB keyboard development details
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i] MCU used: HT82k96E, EM78M611(Em78p612), WT65F5 Since Cypress IC is expensive, most manufacturers still use the above ICs 1. Pure...
songbo Mobile and portable
Newbie question about S3C2440+MCP2515
Newbie question, S3C2440 is connected to MCP2515 (CAN controller) through SPI0, and I am a little confused about interrupts when making the driver. The following is the code executed when SPI0 is init...
happybean Embedded System
What is a servo? What is a servo motor? 
A servo is a device that provides closed-loop feedback signals to control position and speed. Servo is widely used in semiconductor equipment, such as glue coating machines, photolithography machines ...
totopper Industrial Control Electronics
[Jihai M3 core APM32E103VET6S MINI development board] 06. Implement IAP online upgrade function based on Xmodem
APM32E103VET6S has a built-in 512KB FLASH space, and the size of each page is 2KB. We use the USART interface to implement the Xmodem transmission protocol and PC-side software for data transmission, ...
xld0932 Domestic Chip Exchange
Let's discuss how to write this program.
74hc is used for scanning (low level is effective), and then P2 P3 port controls the other 16 ports (high level points light up) How to write a program to make it display Chinese characters? The circu...
HUI535233725 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 876  1189  2292  47  1916  18  24  47  1  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号