EEWORLDEEWORLDEEWORLD

Part Number

Search

PRV6SB0BJYB12202JF

Description
Potentiometer, Cermet, 0.75W, 2000ohm, 38.2V, 5% +/-Tol, -150,150ppm/Cel,
CategoryPassive components    The resistor   
File Size220KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

PRV6SB0BJYB12202JF Overview

Potentiometer, Cermet, 0.75W, 2000ohm, 38.2V, 5% +/-Tol, -150,150ppm/Cel,

PRV6SB0BJYB12202JF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid915910702
Reach Compliance Codecompliant
YTEOL7
structureFully Sealed
JESD-609 codee3
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package length9.5 mm
Package formPanel Mount
method of packingBox
Rated power dissipation(P)0.75 W
resistance2000 Ω
Resistor typePOTENTIOMETER
rotation angle270 deg
seriesPRV6
technologyCERMET
Temperature Coefficient150 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrier
Tolerance5%
Operating Voltage38.2 V
PRV6
www.vishay.com
Vishay Sfernice
Fully Sealed Potentiometer Cermet or Conductive Plastic
FEATURES
PRV6S high power rating 1.5 W at 70 °C (cermet)
PRV6A 0.75 W at 70 °C (conductive plastic)
Tests according to CECC 41000 or IEC 60393-1
Military performances
Low cost
Fully sealed and panel sealed
Compatible RV6 (MIL R 94)
Mechanical endurance 50 000 cycles
Material categorization: For definitions of compliance
please see
www.vishay.com/doc?99912
DIMENSIONS
in millimeters (inches) ± 0.5 mm (± 0.02")
PRV6 STYLE A AND S
9.5 (0.374)
PRV6 STYLE B AND C
12.1 (0.476)
5 (0.200)
0.8 (0.031)
2.5 (0.098)
0.8 (0.031)
SHAFT DIAMETER 3 mm (0.118")
BUSHING A-B-C
SHAFT DIAMETER 3.17 mm (0.125")
BUSHING A-B-C
SHAFT DIAMETER 4 mm (0.157")
BUSHING H-I
(not panel sealed)
B =
see
bushing table
Ø 3 (0.118)
AA
AB
AJ
BA
BB
BJ
Ø 3.17 (0.125)
0.8 (0.031)
EA
EB
EJ
LEADS X = PCB PINS
2.15 (0.085)
0.8 x 0.3 (0.031 x 0.012)
Ø 12.7 (0.50)
LEADS Y = SOLDER LUGS
2.15 (0.085)
1.6 x 0.3 (0.063 x 0.012)
Ø 12.7 (0.50)
5.08 (0.200)
5.08 (0.200)
5.08 (0.200)
0.8 (0.031)
0.5 (0.020)
2.4 (0.094)
Revision: 04-May-12
1
Document Number: 51035
For technical questions, contact:
sfer@vishay.com
- See also Application Notes:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
5.08 (0.200)
Ø 4 (0.157)
A question about i2c bus lock
I recently used an i2c bus ad chip, and now I have this problem: the chip works normally at first, and the values written in and converted are accurate. After working for a period of time (the time is...
flyingxc82 Embedded System
Pingtouge RVB2601 board-NETMGR and WIFI
[i=s]This post was last edited by bigbat on 2021-9-5 15:38[/i]The CH2601 development board integrates the W800 wifi chip, which is a complete set of MCU chips. In theory, the ch2601 main chip does not...
bigbat Domestic Chip Exchange
EVOC obtained the qualification of "Shenzhen Customs Express Taxation Clearance"
In order to reduce the customs declaration time for imported materials and improve the customs clearance efficiency, after the application of the procurement center and the comprehensive evaluation of...
rain Test/Measurement
Thoughts on the M4 debugging program: Experience of entering an erroneous interrupt during program compilation!
During the time I was programming the M4 development board, the most annoying thing for me was entering this function:Although it is stated:This is the code that gets called when the processor receive...
anananjjj Microcontroller MCU
When C51 sends data to computer through serial port, I receive regular garbled characters. Please give me some advice!
void main() { unsigned char Message; //init SP=0x60; SCON = 0x50; TMOD = 0x20; // timer 1 mode 2 auto reload TH1= 0xfa; // 4800 8n1 TL1=0xfa; PCON=0x00; TR1 = 1; // run timer1 TR1=1; while(1) { REN=1;...
fjw10245 Embedded System
About the problem of generating NK.NB0
I use WinCE6.0 as my platform. After each compilation, only nk.bin file is generated. What I need is nk.nb0 file. It is troublesome to convert it through commands each time. I heard on the Internet th...
hulx2007 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1256  268  260  118  613  26  6  3  13  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号