NSPB500S datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > LED optoelectronic/LED> NSPB500S

NSPB500S: DescriptionGENERAL PURPOSE VISIBLE DOME-STYLE LED,BLUE,LED-2B; CategoryLED optoelectronic/LED; File Size233KB，15 Pages; ManufacturerETC

Download Datasheet Parametric View All

NSPB500S Overview

GENERAL PURPOSE VISIBLE DOME-STYLE LED,BLUE,LED-2B

NSPB500S Parametric

Parameter Name	Attribute value
state	ACTIVE

Preview

Download Datasheet

View All

No. STSE-CB2123B

<Cat.No.031112>

SPECIFICATIONS FOR NICHIA

BLUE

LED

MODEL :

NSPB500S

NICHIA CORPORATION

-0-

Nichia STSE-CB2123B

<Cat.No.031112>

7.CAUTIONS

(1) Lead Forming

· When forming leads, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.

Do not use the base of the leadframe as a fulcrum during lead forming.

· Lead forming should be done before soldering.

· Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED’s

characteristics or it may break the LEDs.

· When mounting the LEDs onto a printed circuit board, the holes on the circuit board should be exactly

aligned with the leads of the LEDs. If the LEDs are mounted with stress at the leads, it causes

deterioration of the epoxy resin and this will degrade the LEDs.

(2) Storage

· The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Nichia and

the storage life limits are 3 months.

If the LEDs are stored for 3 months or more, they can be stored

for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.

· Nichia LED leadframes are comprised of a silver plated copper alloy. The silver surface may be

affected by environments which contain corrosive gases and so on. Please avoid conditions which

may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty

during soldering operations. It is recommended that the LEDs be used as soon as possible.

· Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where

condensation can occur.

(3) Static Electricity

· Static electricity or surge voltage damages the LEDs.

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.

· All devices, equipment and machinery must be properly grounded. It is recommended that measures

be taken against surge voltage to the equipment that mounts the LEDs.

· When inspecting the final products in which LEDs were assembled, it is recommended to check

whether the assembled LEDs are damaged by static electricity or not.

It is easy to find

static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).

· Damaged LEDs will show some unusual characteristics such as the leak current remarkably

increases, the forward voltage becomes lower, or the LEDs do not light at the low current.

Criteria : (V

> 2.0V at I

=0.5mA)

-4-

Recommended Resources

Electric vehicle electrical schematic diagram

4 and 1/2 LED digital display (DMS-40PC series)

Toy electronic cat circuit (4)

Sine wave inverter circuit

Lithium battery charger circuit diagram

DT840D/CM3900A type 3 1/2 digital multimeter circuit

Please advise: Hard disk file system problem!: I only know that I can use the diskpart that comes with Windows to view hard disk information. Questions: 1) Where is the file system information of the hard disk stored? 2) What are the methods to vi...; 860122 Embedded System

[Help] Use a single-chip microcomputer to drive an 8-ohm speaker: As the title says, how should I drive it? I searched online, but couldn't find any relevant circuit diagram orz. . . . Tell me how to search :) I want to use two No. 5 batteries to power the system, i...; zgyzsq Embedded System

The static operating point of the transistorThe static operating point of the transistor is refined! ! ! ! !: The static operating point of the transistor The static operating point of the transistor is refined! ! ! ! ! If you don't have enough points or want more information, you can add qq2981952728...; 心晴心情 LED Zone

The maximum number of cycles allowed by STM32F103ZE: I made a program to continuously read and write 24C256 using STM32F103ZE. In order to verify the continuous read and write capability, I planned to write the data of 24C256 at one time, and then read ...; lixmlxm stm32/stm8

About WinCE database API code issues: HANDLE g_hDB; CEOID g_oidDB; int g_nLastSort = PID_NAME;(1) static HANDLE OpenCreateDB(HWND hWnd, int * pnRecords) {int i, rc;CEOIDINFO oidinfo;SORTORDERSPEC sos[4];g_oidDB = 0;g_hDB = CeOpenDatabase(...; wdzywl Embedded System

A little understanding of C2000: ：C2000 is generally used in photovoltaic inverters, digital motor control, digital power supply and other fields. Compared with other MCUs, the core of C2000 is DSP core, so it has strong mathematical...; gaon Power technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components